DS26LS32ACMX Datasheet, PDF (3/13 Pages) Texas Instruments – DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M Quad Differential Line Receivers

DS26LS32AC, DS26LS32C, DS26LS32M, DS26LS33M
www.ti.com
SNLS352C – MAY 1999 – REVISED FEBRUARY 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings⁽¹⁾⁽²⁾
Supply Voltage
Common-Mode Range
Differential Input Voltage
Enable Voltage
Output Sink Current
Maximum Power Dissipation ⁽³⁾ at 25°C
Cavity Package
Molded DIP Package
SOIC Package⁽⁴⁾ DS26LS32
DS26LS32A
Storage Temperature Range
Lead Temperature (Soldering, 4 seconds)
7V
±25V
±25V
7V
50 mA
1433 mW
1362 mW
1002 mW
1051 mW
−65°C to +165°C
260°C
(1) “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to
imply that the device should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device
operation.
(2) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
(3) Derate cavity package 9.6 mW/°C above 25°C; derate molded DIP package 10.9 mW/°C above 25°C.
(4) Derate SOIC Package 8.01 mW/°C for DS26LS32 8.41 mW/°C for DS26LS32A
Operating Conditions
Supply Voltage, (V_CC)
DS26LS32M, DS26LS33M (MIL)
DS26LS32C, DS26LS32AC (COML)
Temperature, (T_A)
DS26LS32M, DS26LS33M (MIL)
DS26LS32C, DS26LS32AC (COML)
Min
Max
Units
4.5
5.5
V
4.75
5.25
V
−55
+125
°C
0
+70
°C
Electrical Characteristics ^{(1) (2) (3)}
over the operating temperature range unless otherwise specified
Symbol
Parameter
Conditions
V_TH
Differential Input Voltage V_OUT = V_OH or DS26LS32, DS26LS32A, −7V ≤ V_CM ≤ +7V
V_OL
DS26LS33, DS26LS33A, −15V ≤ V_CM +15V
R_IN
Input Resistance
−15V ≤ V_CM ≤ +15V (One Input AC GND)
I_IN
Input Current (Under
V _IN = 15V, Other Input −15V ≤ V_IN ≤ +15V
Test)
V _IN = −15V, Other Input −15V ≤ V_IN ≤ +15V
V_OH
Output High Voltage
V_CC = MIN, ΔV_IN = 1V,
Commercial
V_ENABLE = 0.8V, I_OH = −440 μA
Military
V_OL
Output Low Voltage
V_CC = Min, ΔV_IN = −1V,
I_OL = 4 mA
V_ENABLE = 0.8V
I_OL = 8 mA
V_IL
Enable Low Voltage
V_IH
Enable High Voltage
V_I
Enable Clamp Voltage V_CC = Min, I_IN = −18 mA
Min Typ Max Units
−0.2 ±0.07 0.2
V
−0.5 ±0.14 0.5
V
6.0 8.5
kΩ
2.3 mA
−2.8 mA
2.7 4.2
V
2.5 4.2
V
0.4
V
0.45 V
0.8
V
2.0
V
−1.5 V
(1) All currents into device pins are shown as positive, all currents out of device pins are shown as negative, all voltages are referenced to
ground, unless otherwise specified. All values shown as max or min are so classified on absolute value basis.
(2) All typical values are V_CC = 5V, T_A = 25°C.
(3) Only one output at a time should be shorted.
Copyright © 1999–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: DS26LS32AC DS26LS32C DS26LS32M DS26LS33M