OPA2681 Datasheet, PDF (2/22 Pages) Burr-Brown (TI) – Dual Wideband, Current Feedback OPERATIONAL AMPLIFIER With Disable

SPECIFICATIONS: V_S = ±5V
R_F = 402Ω, R_L = 100Ω, and G = +2, (Figure 1 for AC performance only), unless otherwise noted.
OPA2681U, N
PARAMETER
CONDITIONS
TYP
+25°C
+25°C⁽²⁾
GUARANTEED
0°C to
70°C⁽³⁾
–40°C to
+85°C⁽³⁾
UNITS
MIN/ TEST
MAX LEVEL⁽¹⁾
AC PERFORMANCE (Figure 1)
Small-Signal Bandwidth (V_O = 0.5Vp-p)
Bandwidth for 0.1dB Gain Flatness
Peaking at a Gain of +1
Large-Signal Bandwidth
Slew Rate
Rise/Fall Time
Settling Time to 0.02%
0.1%
Harmonic Distortion
2nd Harmonic
3rd Harmonic
Input Voltage Noise
Non-Inverting Input Current Noise
Inverting Input Current Noise
Differential Gain
Differential Phase
Channel-to-Channel Crosstalk
G = +1, R_F = 453Ω
G = +2, R_F = 402Ω
G = +5, R_F = 261Ω
G = +10, R_F = 180Ω
G = +2, V_O = 0.5Vp-p
R_F = 453, V_O = 0.5Vp-p
G = +2, V_O = 5Vp-p
G = +2, 4V Step
G = +2, V_O = 0.5V Step
G = +2, 5V Step
G = +2, V_O = 2V Step
G = +2, V_O = 2V Step
G = +2, f = 5MHz, V_O = 2Vp-p
R_L = 100Ω
R_L ≥ 500Ω
R_L = 100Ω
R_L ≥ 500Ω
f > 1MHz
f > 1MHz
f > 1MHz
G = +2, NTSC, V_O = 1.4Vp, R_L = 150Ω
R_L = 37.5Ω
G = +2, NTSC, V_O = 1.4Vp, R_L = 150Ω
R_L = 37.5Ω
f = 5MHz
DC PERFORMANCE⁽⁴⁾
Open-Loop Transimpedance Gain (Z_OL)
Input Offset Voltage
Average Offset Voltage Drift
Non-Inverting Input Bias Current
Average Non-Inverting Input Bias Current Drift
Inverting Input Bias Current
Average Inverting Input Bias Current Drift
INPUT
Common-Mode Input Range (CMIR)⁽⁵⁾
Common-Mode Rejection (CMR)
Non-Inverting Input Impedance
Inverting Input Resistance (R_I)
OUTPUT
Voltage Output Swing
Current Output, Sourcing
Current Output, Sinking
Closed-Loop Output Impedance
V_O = 0V, R_L = 100Ω
V_CM = 0V
V_CM = 0V
V_CM = 0V
V_CM = 0V
V_CM = 0V
V_CM = 0V
V_CM = 0V
Open-Loop
No Load
100Ω Load
V_O = 0
V_O = 0
G = +2, f = 100kHz
DISABLE (Disabled Low) (SO-14 only)
Power Down Supply Current (+V_S)
Disable Time
Enable Time
Off Isolation
Output Capacitance in Disable
Turn On Glitch
Turn Off Glitch
Enable Voltage
Disable Voltage
Control Pin Input Bias Current (DIS)
POWER SUPPLY
Specified Operating Voltage
Maximum Operating Voltage Range
Max Quiescent Current
Min Quiescent Current
Power Supply Rejection Ratio (–PSRR)
V_DIS = 0, Both Channels
G = +2, 5MHz
G = +2, R_L = 150Ω, V_IN = 0
G = +2, R_L = 150Ω, V_IN = 0
V_DIS = 0, Each Channel
V_S = ±5V
V_S = ±5V
Input Referred
TEMPERATURE RANGE
Specification: U, N
Thermal Resistance, θ_JA
U SO-8
N SO-14
Junction-to-Ambient
280
220
185
125
90
0.4
150
2100
1.7
2.0
12
8
–79
–85
–74
–77
2.5
12
15
0.001
0.008
0.01
0.05
–70
100
±1.3
+30
±10
220
50
2
1600
–73
–77
–71
–75
3.0
14
18
56
±5
+55
±40
±3.5
±3.4
52
47
100 || 2
42
±4.0
±3.9
+190
–150
0.03
±3.8
±3.7
+160
–135
–640
100
25
70
4
±50
±20
3.3
3.5
1.8
1.7
100
160
±5
±6
12
12.8
12
11.2
58
52
–40 to +85
125
100
210
45
4
1600
–70
–70
–71
–74
3.4
15
18
56
±6.5
+35
±65
–400
±50
–125
±3.3
46
±3.7
±3.6
+140
–130
3.6
1.6
160
±6
13.4
10.7
50
190
45
1200
MHz
MHz
MHz
MHz
MHz
dB
MHz
V/µs
ns
ns
ns
ns
typ C
min B
typ C
typ C
min B
max B
typ C
min B
typ C
typ C
typ C
typ C
–68
dBc max B
–69
dBc max B
–68
dBc max B
–72
dBc max B
3.6
nV/√Hz max B
15
pA/√Hz max B
19
pA/√Hz max B
%
typ C
%
typ C
deg
typ C
deg
typ C
dBc
typ C
56
±7.5
+40
±85
–450
±55
–150
kΩ
min A
mV
max A
µV/°C max B
µA
max A
nA/°C max B
µA
max A
nA°/C max B
±3.2
V
min A
45
dB
min A
kΩ || pF typ C
Ω
typ C
±3.6
±3.3
+80
–80
V
min A
V
min A
mA
min A
mA
min A
Ω
typ C
µA
typ C
ns
typ C
ns
typ C
dB
typ C
pF
typ C
mV
typ C
mV
typ C
3.7
V
min A
1.5
V
max A
160
µA
max A
V
typ C
±6
V
max A
13.6
mA
max A
9.7
mA
min A
49
dB
min A
°C
typ C
°C/W typ C
°C/W typ C
NOTES: (1) Test Levels: (A) 100% tested at 25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation.
(C) Typical value only for information. (2) Junction temperature = ambient for 25°C guaranteed specifications. (3) Junction temperature = ambient at low temperature
limit: junction temperature = ambient +23°C at high temperature limit for over temperature guaranteed specifications. (4) Current is considered positive out of node. V_CM
is the input common-mode voltage. (5) Tested < 3dB below minimum specified CMR at ± CMIR limits.
2
OPA2681
SBOS091A