BQ24075-Q1 Datasheet, PDF (2/36 Pages) Texas Instruments – 1.5A USB-FRIENDLY Li-Ion BATTERY CHARGER AND POWER-PATH MANAGEMENT IC

bq24075-Q1
SLUSAU3B – FEBRUARY 2012 – REVISED MARCH 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
DESCRIPTION (CONTINUED)
Additionally, the regulated system input enables instant system turn-on when plugged in even with a totally
discharged battery. The power-path management architecture also permits the battery to supplement the system
current requirements when the adapter cannot deliver the peak system currents, enabling the use of a smaller
adapter.
The battery is charged in three phases: conditioning, constant current, and constant voltage. In all charge
phases, an internal control loop monitors the IC junction temperature and reduces the charge current if the
internal temperature threshold is exceeded. The charger power stage and charge current sense functions are
fully integrated. The charger function has high accuracy current and voltage regulation loops, charge status
display, and charge termination. The input current limit and charge current are programmable using external
resistors.
PART NUMBER
(1) (2)
bq24075QRGTRQ1
V_OVP
6.6 V
ORDERING INFORMATION
V_BAT(REG)
4.2V
V_OUT(REG)
5.5 V
V_DPPM
4.3 V
OPTIONAL
FUNCTION
SYSOFF
MARKING
SAM
(1) The RGT package is available in the following options:
R - taped and reeled in quantities of 3,000 devices per reel.
T - taped and reeled in quantities of 250 devices per reel.
(2) This product is RoHS compatible, including a lead concentration that does not exceed 0.1% of total product weight, and is suitable for
use in specified lead-free soldering processes. In addition, this product uses package materials that do not contain halogens, including
bromine (Br) or antimony (Sb) above 0.1% of total product weight.
ABSOLUTE MAXIMUM RATINGS⁽¹⁾
over the -40°C to 125°C operating free-air temperature range (unless otherwise noted)
VALUE
MIN
MAX
IN (with respect to VSS)
–0.3
28
V_I
Input Voltage
BAT (with respect to VSS)
–0.3
5
OUT, EN1, EN2, CE, TS, ISET, PGOOD, CHG, ILIM,
TMR, SYSOFF
–0.3
7
I_I
Input Current
IN
OUT
I_O
Output Current
(Continuous)
BAT (Discharge mode)
BAT (Charging mode)
1.6
5
5
1.5 ⁽²⁾
Output Sink Current CHG, PGOOD
15
Electrostatic Discharge (HBM) QSS 009-105 (JESD22-A114A)⁽³⁾
1.5
T_J
T_stg
ESD
Rating
Junction temperature
Storage temperature
Human Body Model (HBM) AEC-Q100 Classification Level H2
Charged Device Model (CDM) AEC-Q100 Classification Level C3B
–40
150
–65
150
2
750
UNIT
V
V
V
A
A
A
A
mA
kV
°C
°C
kV
V
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage
values are with respect to the network ground terminal unless otherwise noted.
(2) The IC operational charging life is reduced to 20,000 hours, when charging at 1.5A and 125°C. The thermal regulation feature reduces
charge current if the IC’s junction temperature reaches 125°C; thus without a good thermal design the maximum programmed charge
current may not be reached.
(3) The human body model is a 100-pF capacitor discharged through a 1.5-kΩ resistor into each pin.
2
Copyright © 2012, Texas Instruments Incorporated