DAC2900 Datasheet, PDF (10/21 Pages) Burr-Brown (TI) – Dual, 10-Bit, 125MSPS DIGITAL-TO-ANALOG CONVERTER

The value of the load resistance is limited by the output
compliance specification of the DAC2900. To maintain
specified linearity performance, the voltage for I_OUT and
I_OUT should not exceed the maximum allowable compliance
range.
The two single-ended output voltages can be combined to
find the total differential output swing:
V_OUTDIFF
=
V_OUT
–
V_OUT
=
(2 × Code – 1023)
1024
× I_OUTFS
× R_LOAD
(7)
ANALOG OUTPUTS
The DAC2900 provides two complementary current out-
puts, I_OUT and I_OUT. The simplified circuit of the analog
output stage representing the differential topology is shown
in Figure 2. The output impedance of I_OUT and I_OUT results
from the parallel combination of the differential switches,
along with the current sources and associated parasitic
capacitances.
+V_A
DAC2900
be adapted to the output of the DAC2900 by selecting a
suitable transformer while maintaining optimum voltage
levels at I_OUT and I_OUT. Furthermore, using the differential
output configuration in combination with a transformer will
be instrumental for achieving excellent distortion perfor-
mance. Common-mode errors, such as even-order harmon-
ics or noise, can be substantially reduced. This is particularly
the case with high output frequencies.
For those applications requiring the optimum distortion and
noise performance, it is recommended to select a full-scale
output of 20mA. A lower full-scale range down to 2mA may
be considered for applications that require a low power
consumption, but can tolerate a slightly reduced perfor-
mance level.
OUTPUT CONFIGURATIONS
The current outputs of the DAC2900 allow for a variety of
configurations, some of which are illustrated in Table I. As
mentioned previously, utilizing the converter's differential
outputs will yield the best dynamic performance. Such a
differential output circuit may consist of an RF transformer
or a differential amplifier configuration. The transformer
configuration is ideal for most applications with ac coupling,
while op amps will be suitable for a DC-coupled configura-
tion.
INPUT CODE (D9 - D0)
11 1111 1111
00 0000 0000
00 0000 0000
I_OUT
20mA
10mA
0mA
I_OUT
0mA
10mA
20mA
TABLE I. Input Coding versus Analog Output Current.
I_OUT
R_L
I_OUT
R_L
FIGURE 2. Equivalent Analog Output.
The signal voltage swing that may develop at the two
outputs, I_OUT and I_OUT, is limited by a negative and positive
compliance. The negative limit of –1V is given by the
breakdown voltage of the CMOS process, and exceeding it
will compromise the reliability of the DAC2900, or even
cause permanent damage. With the full-scale output set to
20mA, the positive compliance equals 1.25V, operating with
an analog supply of +V_A = 5V. Note that the compliance
range decreases to about 1V for a selected output current of
I_OUTFS = 2mA. Care should be taken that the configuration
of the DAC2900 does not exceed the compliance range to
avoid degradation of the distortion performance and integral
linearity.
Best distortion performance is typically achieved with the
maximum full-scale output signal limited to approximately
0.5V_PP. This is the case for a 50Ω doubly terminated load
and a 20mA full-scale output current. A variety of loads can
The single-ended configuration may be considered for appli-
cations requiring a unipolar output voltage. Connecting a
resistor from either one of the outputs to ground will convert
the output current into a ground-referenced voltage signal.
To improve on the DC linearity an I-to-V converter can be
used instead. This will result in a negative signal excursion
and, therefore, requires a dual supply amplifier.
DIFFERENTIAL WITH TRANSFORMER
Using an RF transformer provides a convenient way of convert-
ing the differential output signal into a single-ended signal
while achieving excellent dynamic performance (see Figure 3).
The appropriate transformer should be carefully selected based
on the output frequency spectrum and impedance requirements.
The differential transformer configuration has the benefit of
significantly reducing common-mode signals, thus improving
the dynamic performance over a wide range of frequencies.
Furthermore, by selecting a suitable impedance ratio (winding
ratio), the transformer can be used to provide optimum imped-
ance matching while controlling the compliance voltage for the
converter outputs. The model shown, ADTT1-1 (by Mini-
Circuits), has a 1:1 ratio and may be used to interface the
DAC2900 to a 50Ω load. This results in a 25Ω load for each of
the outputs, I_OUT and I_OUT. The output signals are AC coupled
and inherently isolated because of its magnetic coupling.
10
DAC2900
www.ti.com
SBAS166C