|
TPS99110-Q1 Datasheet, PDF (1/63 Pages) Texas Instruments – System-Basis Chip for Automotive Applications | |||
|
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
TPS99110-Q1
SLIS155A â OCTOBER 2014 â REVISED MARCH 2015
TPS99110-Q1 System-Basis Chip for Automotive Applications
1 Features
â¢1 Qualified for Automotive Applications
⢠AEC-Q100 Qualified With the Following Results:
â Device HBM ESD Classification Level 2
â Device CDM ESD Classification Level C4B
⢠Operating Case Temperature: â40°C to 150°C
⢠Ambient Temperature: â40°C to 125°C
⢠Absolute Maximum Junction Temperature: â40°C
to 175°C
⢠Absolute Maximum VBAT: â0.3 to 40 V
⢠Multi-Rail Power Supply
â Two Pre-regulating LDO Controllers: 6-V and
10-V Outputs
â Linear Regulator Controller With External FET:
Adjustable Output From 0.8 to 2.6 V (VDD1)
â 5-V Output Linear Regulator With Internal FET:
400 mA Maximum (VDD5)
â 3.3-V Output Linear Regulator With Internal
FET: 400 mA Maximum (VDD3), Generated
From VDD5
â Voltage Monitoring on VDD1, VDD3, and
VDD5
â 5-V Sensor Supply Output Tracking to VDD5,
100-mA Maximum, Protection Against Short to
Battery and GND
â Two Adjustable Sensor Supplies, 200-mA
Maximum With Protection Against Short to
Battery and GND
â Switched Battery Output Provides VBAT Input
With Low Drop
⢠Analog Features:
â Two Operational Amplifiers for Signal
Conditioning
â Thee Independent Current Loop Interfaces
With Current Sense Input and Digital Output
⢠Microcontroller Interface
â 3.3-V and 5-V Compatible 32-Bit, 2-Mbps SPI
â MCU Monitoring With SPI Q&A Watchdog
⢠Dual Polarity Enable-Drive Outputs for Disabling
Safing-Path or External Power Stages on Any
Detected System Failure
⢠One HS-CAN Transceiver With Bus Wakeup
⢠One KLINE/LIN Transceiver
2 Applications
⢠Transmission Control Unit
⢠Engine Control Unit
3 Description
The TPS99110-Q1 device is a system-basis chip
(SBC) offering a highly integrated solution for the
typical requirements of transmission and engine
electrical control units (ECU) in the automotive space.
The integrated multi-rail power supply is designed to
power microcontroller units (MCUs) and other circuits
in ECUs. The device is designed to support rugged,
high-temperature conditions and incorporates three
low-dropout (LDO) regulators along with three sensor
supplies. The integrated HS-CAN with bus wakeup
and KLINE/LIN transceivers help reduce the
component count on the board. The TPS99110-Q1
functional architecture features undervoltage and
overvoltage monitoring, current limits, temperature
warning flags, and overtemperature shutdown on all
regulator outputs. Additional features include a
window watchdog and SPI Q&A watchdog for MCU-
monitoring.
The device is available in a 64-pin HTQFP (PAP)
PowerPAD⢠integrated circuit package.
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
TPS99110-Q1
HTQFP (64)
10.00 mm à 10.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic of Typical Application
TPS99110-Q1
Op
Amps
GPIO and
ADC Input
SPI Bus
Watchdog
PRE1 Regulator
Sensor Supply
ADC
MCU
TXD
RXD
TXD
RXD
GPIO
K-LINE/LIN
Interface
CAN Interface
VDD5
LDO
VDD1
VDD3
LDO
PRE2
Regulator
Current-Loop
Interface
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
|
▷ |