TPS2547 Datasheet, PDF (1/42 Pages) Texas Instruments – USB Charging Port Controller and 3-Amp Power Switch With Load Detection

Product
Folder
Order
Now
Technical
Documents
Tools &
Software
Support &
Community
TPS2547
SLVSE11A – MAY 2017 – REVISED MAY 2017
TPS2547 USB Charging Port Controller and 3-Amp Power Switch With Load Detection
1 Features
•1 D+/D– CDP/DCP Modes per USB BC 1.2
• D+/D– Shorted Mode per Chinese
Telecommunication Industry Standard YD/T
1591-2009
• Supports Non-BC1.2 Charging Modes by
Automatic Selection:
– D+/D– Divider Modes 2 V/2.7 V and 2.7 V/2 V
– D+/D– 1.2-V Mode
• Supports Sleep-Mode Charging and
Mouse/Keyboard Wakeup
• Load Detection for Power Supply Control in S4/S5
Charging and Port Power Management in All
Charge Modes
• USB 2.0 and 3.0 Compatible
• Integrated 73-mΩ (Typical) High-Side MOSFET
• 3-A Programmable I_LIMIT Supports 15 Watt Loads
• Operating Range: 4.5 V to 5.5 V
• 2 µA/270 µA I_Q When Disabled/Enabled
• Drop-In, BOM Compatible with TPS2543/46
• 16-Pin WQFN (3.00 mm × 3.00 mm) Package
• 8-kV ESD Rating on DM/DP Pins
• UL Recognized File No. E169910 and CB
Certified - Pending
2 Applications
• USB Ports (Host and Hubs)
• Notebook and Desktop PCs
• Universal Wall-Charging Adapters
3 Description
The TPS2547 is a USB charging port controller and
power switch with an integrated USB 2.0 high-speed
data line (D+/D–) switch. TPS2547 provides the
electrical signatures on D+/D– to support charging
schemes listed in Feature Description section. TI
tests charging of popular mobile phones, tablets, and
media devices with the TPS2547 to ensure
compatibility with both BC1.2 compliant, and non-
BC1.2 compliant devices.
In addition to charging popular devices, the TPS2547
also supports two distinct power management
features, namely, power wake and port power
management (PPM) through the STATUS pin. Power
wake allows for power supply control in S4/S5
charging and PPM supports intelligent port power
management in multiport systems. Additionally,
system wake up (from S3) with a mouse/keyboard
(both low speed and full speed) is fully supported in
the TPS2547.
The TPS2547 73-mΩ power-distribution switch is
intended for applications where heavy capacitive
loads and short-circuits are likely to be encountered.
Two programmable current thresholds provide
flexibility for setting current limits and load detect
thresholds.
Device Information⁽¹⁾
PART NUMBER
PACKAGE
BODY SIZE (NOM)
TPS2547
WQFN (16)
3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
To Portable Device à
Power Bus ^{4.5V – 5.5V}
0.1 uF
IN
OUT
RSTATUS
(10 kW)
RFAULT
(10 kW)
TPS2547
ILIM_LO
ILIM_HI
STATUS Signal
STATUS
RILIM_HI
CUSB
RILIM_LO
VBUS
D-
D+
GND
Fault Signal
FAULT
GND
ILIM Select
Power Switch EN
Mode Select I/O
ILIM_SEL
EN
CTL1
CTL2
CTL3
DM_IN
DP_IN
DM_OUT
DP_OUT
USB
Connector
To Host Controller à
Copyright © 2017, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.