TPIC2040 Datasheet, PDF (1/57 Pages) Texas Instruments – Serial I/F Controlled 7-Channel Motor-Driver

Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
TPIC2040
SLIS172 – DECEMBER 2015
TPIC2040 Serial I/F Controlled 7-Channel Motor-Driver for ODD Drive
1 Features
•1 Serial Peripheral Interface (SPI)
– Maximum Read/Write 35 MHz
– 3.3-V Digital I/O
• Actuator and Motor Driver
– PWM Control With H-Bridge Output
– Focus / Tracking / Tilt Actuator Driver With 12-
Bit DAC Control
– Sled Motor Drivers With Current Mode, 10-Bit
DAC Control
– Load Driver With 12-Bit DAC Control
– Capable End Position Sensing for Sled
Without Position Sensor
• Spindle Motor Driver
– Integrated Spindle Current Sense Resistor
– Selectable Current Sense Resistor Value 0.27
to 0.20 Ω by Register Setting; Thereby, SPM
Current can be Restricted from 725 to 980 mA
– Sensor-Less: Rotor Position Sense by Motor
BEMF
– 12-Bit Spindle DAC Programmed Through
Serial Port
– Self-Contained Inductive Position Sense and
Startup
– Quick Stop by Automatic Controlled Brake
Named Auto Short Brake (Short and Active
Brake)
– 0.7-A Maximum Continuous Current Excluding
Thermal Issues
– LS Mode: Restricted to 25% of Normal Speed
• Utility Functions
– XRESET Signal With Digital Delay (POR) 20
ms
– Status Latch: Act Timer, SIF Error, PWR
Monitor, Thermal Protection, and OCP Error
• Switch
– CSW: Software Control Current Output Port
• LDO Pre-Driver
– 1-Channel LDO Pre-Driver for 3.3-V or 1.2-V
Output With External Transistor
• Protection
– Individual Thermal Protect Circuit on CSW,
SPM, and Act Channel
– Two Alert Levels: Pre-Detect and Detect in
Thermal Protection
– Overcurrent Protection Circuit in Load Driver
1
– Selectable OCP Threshold Level in CSW
Output
– Hardware Device Disable Pin XMUTE
– Power Monitor by Undervoltage Lockout
(UVLO) and Overvoltage Protection (OVP)
2 Applications
• DVD Player
• CD Player
• Optical Disk Drive
3 Description
TPIC2040 is a very-low noise type motor driver IC
suitable for slim or ultra-slim DVD reader/writer. This
IC includes integrated current sense resistance that
measures SPM current and reduces drive system
cost. The 7-channel driver IC controlled by serial I/F
is optimum for driving a spindle motor, a sled motor,
a load motor, and Focus / Tracking / Tilt actuators.
The spindle motor driver uses BEMF detection for
sensorless startup and control of the spindle motor
Device Information⁽¹⁾
PART NUMBER
PACKAGE
BODY SIZE (NOM)
TPIC2040DBT
TSSOP (38)
9.70 mm × 4.40 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Block Diagram
5V
3.3 V
SPI
1PX V
output ^{5 V}
9Vout
LIN9VG
LINFB
TPIC2040
LDO
Control
5V
SPM
Driver
5V
SLED1
5V
SLED2
5V
TLT
5V
FCS
5V
TRK
5V
LOAD
MCOM
U
V
W
SLED1+
SLED1-
SLED2+
SLED2-
TLT+
TLT-
FCS+
FCS-
TRK+
TRK-
LOAD+
LOAD-
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.