TAS2555 Datasheet, PDF (1/12 Pages) Texas Instruments – Class-D Mono Audio Amplifier

Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
TAS2555
SLASE98A – AUGUST 2015 – REVISED AUGUST 2015
TAS2555 5.7-W Class-D Mono Audio Amplifier with Class-H Boost and Speaker Sense
1 Features
•1 Ultra Low-Noise Mono Boosted Class-D Amplifier
– 5.7 W at 1% THD+N and 6.9 W at 10%
THD+N into 4-Ω Load from 4.2-V Supply
– 3.8 W at 1% THD+N and 4.5 W at 10%
THD+N into 8-Ω Load from 4.2-V Supply
• Output Noise for DAC + Class-D(ICN) is 15.9 µV
• DAC + Class-D SNR 111 dB at 1%THD+N/8 Ω
• THD+N –90 dB at 1 W / 8 Ω with Flat Frequency
Response
• PSRR 110 dB for 200 mV_pp ripple at 217 Hz
• Input Sample Rates from 8 kHz to 96 kHz
• Built-In Speaker Sense
– Measures Speaker Current and Voltage
– Measures VBAT Voltage, Chip Temperature
• Dedicated Real-Time DSP for Speaker Protection
– Thermal and Excursion Protection
– Detects Leak and Damaged Speaker
• High Efficiency Class-H Boost Converter With
Multi-Level Tracking
– 86% at 500 mW in 8 Ω with 3.6 V V_BAT
– 87% at 700 mW in 8 Ω with 4.2 V V_BAT
• Built-In Automatic Gain Control (AGC)
– Limits Battery Current Consumption
• Adjustable Class-D Switching Edge-Rate Control
• Power Supplies
– Boost Input: 2.9 V to 5.5 V
– Analog/Digital: 1.65 V to 1.95 V
– Digital I/O: 1.62 V to 3.6 V
• Thermal, Short-Circuit, and Under-Voltage
Protection
• I2S, Left-Justified, Right-Justified, DSP, and TDM
Input and Output Interface,
• I²C or SPI Interface for Register Control
• 3.47 mm x 3.23 mm, 0.5 mm pitch, 42-ball WCSP
• Stereo Configuration Using Two TAS2555
Devices
2 Applications
• Mobile Phones
• Tablets
• Portable Audio Docks
• Bluetooth Speakers
3 Description
The TAS2555 is a state-of-the-art Class-D audio
amplifier which is a full system on a Chip (SoC). The
device features a ultra low-noise audio DAC and
Class-D power amplifier which incorporates speaker
voltage and current sensing feedback. An on-chip,
low-latency DSP supports Texas Instruments
SmartAmp speaker protection algorithms to
maximizes loudness while maintaining safe speaker
conditions.
The device can be used easily with any processor
with an I2S output and stereo implementations are
possible when using two TAS2555 devices. Separate
tuning for different speakers is supported allowing
customers to add value while maintaining form factor
designs. Additionally, the TAS2555 supports separate
voice and audio tuning dynamically with ultra-low 15.9
µV ICN regardless of mode of operation making
receiver/speaker implementations possible.
A Class-H boost converter generates the Class-D
amplifier supply rail. When the audio signal only
requires a lower Class-D output power, the boost
improves system efficiency by deactivating and
connecting V_BAT directly to the Class-D amplifier
supply. When higher audio output power is required,
the multi-level boost quickly activates tracking the
signal to provide the additional voltage to the load.
Device Information⁽¹⁾
PART NUMBER
PACKAGE
BODY SIZE (NOM)
TAS2555
WCSP (42)
3.47 mm x 3.23 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
L1
MCLK
I2S
4
I2C
2
/RESET
VBAT
2 SW
C1
VREG
TAS2555
VBOOST
2
C2
Ferrite bead
(optional)
OUT+
+
OUT-
To Speaker
-
Ferrite bead
(optional)
VSENSE+
VSENSE-
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.