SN74LVTH244A-EP Datasheet, PDF (1/9 Pages) Texas Instruments – 3.3-V ABT OCTAL BUFFER/DRIVER WITH 3-STATE OUTPUTS

D Controlled Baseline
− One Assembly/Test Site, One Fabrication
Site
D Extended Temperature Performance of
−40°C to 125°C
D Enhanced Diminishing Manufacturing
Sources (DMS) Support
D Enhanced Product-Change Notification
D Qualification Pedigree^†
D Supports Mixed-Mode Signal Operation
(5-V Input and Output Voltages With
3.3-V V_CC)
D Typical V_OLP (Output Ground Bounce)
<0.8 V at V_CC = 3.3 V, T_A = 25°C
D Supports Unregulated Battery Operation
Down to 2.7 V
D I_off and Power-Up 3-State Support Hot
Insertion
† _{Component qualification in accordance with JEDEC and industry}
standards to ensure reliable operation over an extended
temperature range. This includes, but is not limited to, Highly
Accelerated Stress Test (HAST) or biased 85/85, temperature
cycle, autoclave or unbiased HAST, electromigration, bond
intermetallic life, and mold compound life. Such qualification
testing should not be viewed as justifying use of this component
beyond specified performance and environmental limits.
SN74LVTH244AĆEP
3.3ĆV ABT OCTAL BUFFER/DRIVER
WITH 3ĆSTATE OUTPUTS
SCAS691C − APRIL 2003 − REVISED OCTOBER 2003
D Bus Hold on Data Inputs Eliminates the
Need for External Pullup/Pulldown
Resistors
D Latch-Up Performance Exceeds 500 mA Per
JESD 17
D ESD Protection Exceeds JESD 22
− 2000-V Human-Body Model (A114-A)
− 200-V Machine Model (A115-A)
DB OR PW PACKAGE
(TOP VIEW)
1OE 1
1A1 2
2Y4 3
1A2 4
2Y3 5
1A3 6
2Y2 7
1A4 8
2Y1 9
GND ¹⁰
20 V_CC
19 2OE
18 1Y1
17 2A4
16 1Y2
15 2A3
14 1Y3
13 2A2
12 1Y4
11 2A1
description/ordering information
This octal buffer and line driver is designed specifically for low-voltage (3.3-V) V_CC operation, but with the
capability to provide a TTL interface to a 5-V system environment.
The SN74LVTH244A is organized as two 4-bit line drivers with separate output-enable (OE) inputs. When OE
is low, the device passes data from the A inputs to the Y outputs. When OE is high, the outputs are in the
high-impedance state.
To ensure the high-impedance state during power up or power down, OE should be tied to V_CC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup
or pulldown resistors with the bus-hold circuitry is not recommended.
ORDERING INFORMATION
TA
PACKAGE^‡
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
SSOP − DB
−40°C to 125°C
TSSOP − PW
Tape and reel
Tape and reel
SN74LVTH244AQDBREP
SN74LVTH244AQPWREP
LH244AEP
LH244AEP
‡ _{Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are}
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
Copyright  2003, Texas Instruments Incorporated
1