SN54ACT1284_16 Datasheet, PDF (1/17 Pages) Texas Instruments – 7-BIT BUS INTERFACES WITH 3-STATE OUTPUTS

SN54ACT1284, SN74ACT1284
7ĆBIT BUS INTERFACES
WITH 3ĆSTATE OUTPUTS
SCAS459D − NOVEMBER 1994 − REVISED OCTOBER 2003
D 4.5-V to 5.5-V V_CC Operation
D Inputs Accept Voltages to 5.5 V
D Max t_pd of 20 ns at 5 V
D 3-State Outputs Directly Drive Bus Lines
D Flow-Through Architecture Optimizes PCB
Layout
D Center-Pin V_CC and GND Configurations
Minimize High-Speed Switching Noise
D ESD Protection Exceeds JESD 22
− 2000-V Human-Body Model (A114-A)
− 200-V Machine Model (A115-A)
D Designed for the IEEE 1284-I (Level-1 Type)
and IEEE 1284-II (Level-2 Type) Electrical
Specifications
description/ordering information
SN54ACT1284 . . . J OR W PACKAGE
SN74ACT1284 . . . DB, DW, NS, OR PW PACKAGE
(TOP VIEW)
A1 1
A2 2
A3 3
A4 4
GND 5
GND 6
A5 7
A6 ⁸
A7 ⁹
DIR ¹⁰
20 B1
19 B2
18 B3
17 B4
16 V_CC
15 V_CC
14 B5
13 _B6
12 _B7
11 _HD
SN54ACT1284 . . . FK PACKAGE
(TOP VIEW)
The ’ACT1284 devices are designed for
asynchronous two-way communication between
data buses. The control function minimizes
external timing requirements.
The devices allow data transmission in either the
A-to-B or the B-to-A direction for bits 1, 2, 3, and
4, depending on the logic level at the
direction-control (DIR) input. Bits 5, 6, and 7,
however, always transmit in the A-to-B direction.
A4
GND
GND
A5
A6
3 2 1 20 19
4
18
5
17
6
16
7
15
8
14
9 10 11 12 13
B3
B4
V_CC
V_CC
B5
The output drive for each mode is determined by the high-drive (HD) control pin. When HD is high, the high drive
is delivered by the totem-pole configuration, and when HD is low, the outputs are open drain. This meets the
drive requirements as specified in the IEEE 1284-I (level-1 type) and the IEEE 1284-II (level-2 type) parallel
peripheral-interface specification.
ORDERING INFORMATION
TA
PACKAGE†
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
SOIC − DW
Tube
Tape and reel
SN74ACT1284DW
SN74ACT1284DWR
ACT1284
0°C to 70°C
SOP − NS
SSOP − DB
Tape and reel
Tape and reel
SN74ACT1284NSR
SN74ACT1284DBR
ACT1284
AU284
TSSOP − PW
Tube
Tape and reel
SN74ACT1284PW
SN74ACT1284PWR
AU284
CDIP − J
Tube
SNJ54ACT1284J
SNJ54ACT1284J
−55°C to 125°C CFP − W
Tube
SNJ54ACT1284W
SNJ54ACT1284W
LCCC − FK
Tube
SNJ54ACT1284FK
SNJ54ACT1284FK
† _{Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are}
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains PRODUCTION
DATA information current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all
parameters.
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
Copyright  2003, Texas Instruments Incorporated
1