SN54ABT16374 Datasheet, PDF (1/8 Pages) Texas Instruments – 16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS

SN54ABT16374, SN74ABT16374
16ĆBIT EDGEĆTRIGGERED DĆTYPE FLIPĆFLOPS
WITH 3ĆSTATE OUTPUTS
SCBS454 - APRIL 1991 - REVISED JULY 1993
• Members of the Texas Instruments
Widebus  Family
• State-of-the-Art EPIC-ΙΙB BiCMOS Design
Significantly Reduces Power Dissipation
• ESD Protection Exceeds 2000 V Per
MIL-STD-883C, Method 3015; Exceeds
200 V Using Machine Model (C = 200 pF,
R = 0)
• Latch-Up Performance Exceeds 500 mA Per
JEDEC Standard JESD-17
• Typical V_OLP (Output Ground Bounce)
< 0.8 V at V_CC = 5 V, T_A = 25°C
• Distributed V_CC and GND Pin Configuration
Minimizes High-Speed Switching Noise
• Flow-Through Architecture Optimizes PCB
Layout
• High-Drive Outputs (− 32-mA I_OH,
64-mA I_OL)
• Packaged in Plastic 300-mil Shrink
Small-Outline Packages (DL) and 380-mil
Fine-Pitch Ceramic Flat Packages (WD)
Using 25-mil Center-to-Center Spacings
description
The ’ABT16374 is a 16-bit edge-triggered D-type
flip-flop with 3-state outputs designed specifically
for driving highly capacitive or relatively
low-impedance loads. It is particularly suitable for
implementing buffer registers, I/O ports,
bidirectional bus drivers, and working registers.
SN54ABT16374 . . . WD PACKAGE
SN74ABT16374 . . . DL PACKAGE
(TOP VIEW)
1OE 1
1Q1 2
1Q2 3
GND 4
1Q3 5
1Q4 6
V_CC 7
1Q5 8
1Q6 9
GND 10
1Q7 11
1Q8 12
2Q1 13
2Q2 14
GND 15
2Q3 16
2Q4 17
V_CC 18
2Q5 19
2Q6 20
GND 21
2Q7 22
2Q8 23
2OE 24
48 1CLK
47 1D1
46 1D2
45 GND
44 1D3
43 1D4
42 V_CC
41 1D5
40 1D6
39 GND
38 1D7
37 1D8
36 2D1
35 2D2
34 GND
33 2D3
32 2D4
31 V_CC
30 2D5
29 2D6
28 GND
27 2D7
26 2D8
25 2CLK
The device can be used as two 8-bit flip-flops or one 16-bit flip-flop. On the positive transition of the clock (CLK)
input, the Q outputs of the flip-flop take on the logic levels set up at the data (D) inputs.
A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high
or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive
the bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus
lines without need for interface or pullup components
The output enable (OE) does not affect internal operations of the flip-flop. Old data can be retained or new data
can be entered while the outputs are in the high-impedance state.
To ensure the high-impedance state during power up or power down, OE should be tied to V_CC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
The SN74ABT16374 is packaged in TI’s shrink small-outline package (DL), which provides twice the I/O pin
count and functionality of standard small-outline packages in the same printed-circuit-board area.
The SN54ABT16374 is characterized for operation over the full military temperature range of −55°C to 125°C.
The SN74ABT16374 is characterized for operation from − 40°C to 85°C.
Widebus and EPIC-ΙΙB are trademarks of Texas Instruments Incorporated.
UNLESS OTHERWISE NOTED this document contains PRODUCTION
DATA information current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all
parameters.
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
• POST OFFICE BOX 1443 HOUSTON, TEXAS
77251−1443
Copyright  1993, Texas Instruments Incorporated
1