PT7773 Datasheet, PDF (1/3 Pages) Texas Instruments – 32 AMP HIGH-PERFORMANCE SLEDGE HAMMER” PROGRAMMABLE ISR

For assistance or to order, call [phone]
PT7773
5V
32 AMP HIGH-PERFORMANCE
“SLEDGE HAMMER” PROGRAMMABLE ISR
SLTS078
(Revised 5/31/2000)
Description
The PT7773 is one of a series of
high-performance, 32 Amp Integrated
Switching Regulators (ISRs) housed in
a 27-pin SIP package. The 32A capa-
bility allows easy integration of the
latest high-speed, low-voltage µPs,
ASICs, DSPs, and bus drivers into
existing 5V systems.
The output voltage of the PT7773
is programmable over the low volt-
age range, 0.8V to 3.1V via a 5-bit
input. A differential remote sense is
also provided, which automatically
compensates for any voltage drop
between the ISR and load.
An output capacitance of 2400µF
is required for proper operation.
Standard Application
PROGRAMMING PINS
VID0
VID1
VID2
VID3
VID4
V_IN
L1
1H
6432 1
26
7 - 11 _PT7773
REMOTE SENSE (+)
20 - 25
V_OUT
SYNC OUT
GND
STBY*
Specifications
+
C_IN
27
13 - 19 5 12
Cin = Required 2400µF electrolytic
Cout = Required 2400µF electrolytic
L1 = Optional 1µH input choke
+
C_OUT
LOAD
GND
REMOTE SENSE (-)
Pin-Out Information
Pin Function
Pin Function
1 VID0
2 VID1
3 VID2
4 VID3
14 GND
15 GND
16 GND
17 GND
5 STBY*- Stand-by
6 VID4
7 V_in
8 V_in
9 V_in
10 V_in
11 V_in
12 Remote Sense Gnd
13 GND
18 GND
19 GND
20 Vout
21 Vout
22 Vout
23 Vout
24 Vout
25 Vout
26 Remote Sense Vout
27 Sync Out
For STBY* pin; open = output enabled;
ground = output disabled.
Characteristics
(T _a = 25°C unless noted)
Output Current
Input Voltage Range
Output Voltage Tolerance
Line Regulation
Load Regulation
Vo Ripple/Noise pk-pk
Transient Response
with Cout = 2400µF
Efficiency
Switching Frequency
Absolute Maximum
Operating Temperature Range
Storage Temperature
Weight
Symbols
Io
Vin
∆V_o
Reg_line
Regload
Vn
t_tr
Vos
η
ƒo
Ta
Ts
—
Conditions
Ta = +60°C, 200 LFM, pkg N
Ta = +25°C, natural convection
0.1A ≤ Io ≤ 32A
V_in = +5V, I_o = 32A
0°C ≤ Ta ≤ +55°C
4.5V ≤ V_in ≤ 5.5V, I_o = 32A
Vin = +5V, 0.1 ≤ Io ≤ 32A
Vin = +5V, Io = 32A
I_o step between 16A and 32A
Vo over/undershoot
V_in = +5V, I_o = 20A, V_o = 2.5V
4.5V ≤ Vin ≤ 5.5V
0.1A ≤ I_o ≤ 32A
Over Vin Range
—
Vertical/Horizontal
PT7773 SERIES
Min
Typ
Max
0.1⁽¹⁾
—
32
0.1(1)
—
26
4.5
—
5.5
Vo-0.03 —
Vo+0.03
—
±10
—
—
±10
—
—
50
—
—
100
—
—
200
—
—
86
—
650
700
750
Units
A
V
V
mV
mV
mV
µSec
mV
%
kHz
0
—
+85 ⁽²⁾
°C
-40
—
+125
°C
—
53/66
—
grams
Notes: (1) ISR-will operate down to no load with reduced specifications. Please note that this product is not short-circuit protected.
(2) See SOA curves or consult the factory for the appropriate derating.
Output Capacitors: The PT7773 series requires a minimum output capacitance of 2400µF for proper operation. Do not use Oscon type capacitors. The maximum allow-
able output capacitance is 30,000µF.
Input Filter: An input filter is optional for most applications. The input inductor must be sized to handle 32ADC with a typical value of 1µH. The input capacitance must
be rated for a minimum of 2.6Arms of ripple current. For transient or dynamic load applications, additional capacitance may be required.
Power Trends, Inc. 27715 Diehl Road, Warrenville, IL 60555 [phone] Fax: [phone] http://www.ti.com/powertrends