MSP430F2619S-HT_16 Datasheet, PDF (1/99 Pages) Texas Instruments – Mixed-Signal Microcontroller

Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
MSP430F2619S-HT
SLAS697E – MARCH 2010 – REVISED NOVEMBER 2016
MSP430F2619S-HT Mixed-Signal Microcontroller
1 Device Overview
1.1 Features
1
• Low-Supply Voltage Range 1.8 V to 3.6 V
• Ultra-Low Power Consumption
– Active Mode: 365 μA at 1 MHz, 2.2 V
– Standby Mode (VLO): 0.5 μA
– Off Mode (RAM Retention): 0.1 μA
• Wake-Up From Standby Mode in Less than 1 μs
• 16-Bit RISC Architecture, 62.5-ns Instruction Cycle
Time
• Three-Channel Internal DMA
• 12-Bit Analog-to-Digital (A/D) Converter With
Internal Reference, Sample-and-Hold, and
Autoscan Feature
• Dual 12-Bit Digital-to-Analog (D/A) Converters With
Synchronization
• 16-Bit Timer_A With Three Capture/Compare
Registers
• 16-Bit Timer_B With Seven Capture/Compare-
With-Shadow Registers
• On-Chip Comparator
• Four Universal Serial Communication Interfaces
(USCIs)
– USCI_A0 and USCI_A1
– Enhanced UART Supporting Auto-Baud-Rate
Detection (LIN)
– IrDA Encoder and Decoder
– Synchronous SPI
– USCI_B0 and USCI_B1
– I²C
– Synchronous SPI
• Supply Voltage Supervisor/Monitor With
Programmable Level Detection
• Brownout Detector
• Bootstrap Loader
• Serial Onboard Programming, No External
Programming Voltage Needed Programmable
Code Protection by Security Fuse
• MSP430F2619S 120KB + 256B Flash Memory,
4KB RAM
• Available in 64-Pin QFP Package or 64-Pin and
80-Pin KGD Options
• For Complete Module Descriptions, Refer to
MSP430x2xx Family User's Guide (SLAU144).
1.2 Applications
• Supports Extreme Temperature Applications:
– Controlled Baseline
– One Assembly/Test Site
– One Fabrication Site
– Extended Product Life Cycle
– Extended Product-Change Notification
– Product Traceability
• This device is qualified for 1000 hours of
continuous operation at maximum rated
temperature.
• TI high-temperature products use highly-optimized
silicon (die) solutions with design and process
enhancements to maximize performance over
extended temperatures.
1.3 Description
The MSP430F2619S ultra-low-power microcontroller features different sets of peripherals targeted for
various applications. The architecture, combined with five low-power modes, is optimized to achieve
extended battery life in portable measurement applications. The device features a powerful 16-bit RISC
CPU, 16-bit registers, and constant generators that attribute to maximum code efficiency. The digitally
controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 1 μs.
The MSP430F2619S is a microcontroller configuration with two built-in 16-bit timers, a fast 12-bit A/D
converter, a comparator, dual 12-bit D/A converters, four universal serial communication interface (USCI)
modules, DMA, and up to 64 I/O pins.
Typical applications include sensor systems that capture analog signals, convert them to digital values,
and then process the data for display or for transmission to a host system. Stand-alone RF sensor front
end is another area of application.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.