ISO7730-Q1 Datasheet, PDF (1/38 Pages) Texas Instruments – High-Speed, Robust-EMC Reinforced Triple-Channel Digital Isolators

Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
ISO7730-Q1, ISO7731-Q1
SLLSEU3 – NOVEMBER 2016
ISO773x-Q1 High-Speed, Robust-EMC Reinforced Triple-Channel Digital Isolators
1 Features
•1 Qualified for Automotive Applications
• AEC-Q100 Qualified With the Following Results:
– Device Temperature Grade 1: –40°C to
+125°C Ambient Operating Temperature
– Device HBM ESD Classification Level 3A
– Device CDM ESD Classification Level C6
• Signaling Rate: Up to 100 Mbps
• Wide Supply Range: 2.25 V to 5.5 V
• 2.25-V to 5.5-V Level Translation
• Default Output High and Low Options
• Low Power Consumption, Typical 1.5 mA per
Channel at 1 Mbps
• Low Propagation Delay: 11 ns Typical
(5-V Supplies)
• High CMTI: ±100 kV/μs Typical
• Robust Electromagnetic Compatibility (EMC)
– System-Level ESD, EFT, and Surge Immunity
– Low Emissions
• Isolation Barrier Life: >40 Years
• Wide-SOIC (DW-16) and QSOP (DBQ-16)
Package Options
• Safety-Related Certifications:
– Reinforced Insulation per DIN V VDE V 0884-
10 (VDE V 0884-10):2006-12
– 5000 V_RMS (DW) and 2500 V_RMS (DBQ)
Isolation Rating per UL 1577
– CSA Component Acceptance Notice 5A, IEC
60950-1 and IEC 60601-1 End Equipment
Standards
– CQC Certification per GB4943.1-2011
– TUV Certification according to EN 60950-1 and
EN 61010-1
– Certifications for DW Package Complete; All
Other Certifications are Planned
2 Applications
• Hybrid Electric Vehicles
• Motor Control
• Power Supplies
• Solar Inverters
• Medical Equipment
1
3 Description
The ISO773x-Q1 devices are high-performance,
triple-channel digital isolators with 5000 V_RMS (DW
package) and 2500 V_RMS (DBQ package) isolation
ratings per UL 1577.
This family of devices has reinforced insulation
ratings according to VDE, CSA, TUV and CQC.
The ISO773x-Q1 family of devices provides high
electromagnetic immunity and low emissions at low
power consumption, while isolating CMOS or
LVCMOS digital I/Os. Each isolation channel has a
logic input and output buffer separated by a silicon
dioxide (SiO₂) insulation barrier. This device comes
with enable pins which can be used to put the
respective outputs in high impedance for multi-master
driving applications and to reduce power
consumption. The ISO7730-Q1 device has all three
channels in the same direction and the ISO7731-Q1
device has two forward and one reverse-direction
channel. If the input power or signal is lost, the
default output is high for devices without suffix F and
low for devices with suffix F. See the Device
Functional Modes section for further details.
Used in conjunction with isolated power supplies, this
device helps prevent noise currents on a data bus or
other circuits from entering the local ground and
interfering with or damaging sensitive circuitry.
Through innovative chip design and layout
techniques, electromagnetic compatibility of the
ISO773x-Q1 device has been significantly enhanced
to ease system-level ESD, EFT, surge, and
emissions compliance. The ISO773x-Q1 family of
devices is available in 16-pin wide-SOIC and QSOP
packages.
Device Information⁽¹⁾
PART NUMBER
PACKAGE BODY SIZE (NOM)
ISO7730-Q1
ISO7731-Q1
SOIC (DW)
SSOP (DBQ)
10.30 mm × 7.50 mm
4.90 mm × 3.90 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Simplified Schematic
V_CCI
Isolation
Capacitor
V_CCO
INx
OUTx
ENx
GNDI
GNDO
V_CCI and GNDI are supply and ground
connections, respectively, for the input
channels.
V_CCO and GNDO are supply and ground
connections, respectively, for the output
channels.
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.