CDCVF857_16 Datasheet, PDF (1/22 Pages) Texas Instruments – 2.5-V PHASE-LOCKED-LOOP CLOCK DRIVER

CDCVF857
www.ti.com
SCAS047F – MARCH 2003 – REVISED MAY 2007
2.5-V PHASE-LOCKED-LOOP CLOCK DRIVER
FEATURES
• Spread-Spectrum Clock Compatible
• Operating Frequency: 60 MHz to 220 MHz
• Low Jitter (Cycle-Cycle): ±35 ps
• Low Static Phase Offset: ±50 ps
• Low Jitter (Period): ±30 ps
• 1-to-10 Differential Clock Distribution (SSTL2)
• Best in Class for V_OX = V_DD/2 ±0.1 V
• Operates From Dual 2.6-V or 2.5-V Supplies
• Available in a 40-Pin MLF Package, 48-Pin
TSSOP Package, 56-Ball MicroStar Junior™
BGA Package
• Consumes < 100-µA Quiescent Current
• External Feedback Pins (FBIN, FBIN) Are Used
to Synchronize the Outputs to the Input
Clocks
• Meets/Exceeds JEDEC Standard (JESD82-1)
For DDRI-200/266/333 Specification
• Meets/Exceeds Proposed DDRI-400
Specification (JESD82-1A)
• Enters Low-Power Mode When No CLK Input
Signal Is Applied or PWRDWN Is Low
APPLICATIONS
• DDR Memory Modules (DDR400/333/266/200)
• Zero-Delay Fan-Out Buffer
DESCRIPTION
The CDCVF857 is a high-performance, low-skew,
low-jitter, zero-delay buffer that distributes a
differential clock input pair (CLK, CLK) to 10
differential pairs of clock outputs (Y[0:9], Y[0:9]) and
one differential pair of feedback clock outputs
(FBOUT, FBOUT). The clock outputs are controlled
by the clock inputs (CLK, CLK), the feedback clocks
(FBIN, FBIN), and the analog power input (AVDD).
When PWRDWN is high, the outputs switch in phase
and frequency with CLK. When PWRDWN is low, all
outputs are disabled to a high-impedance state
(3-state) and the PLL is shut down (low-power
mode). The device also enters this low-power mode
when the input frequency falls below a suggested
detection frequency that is below 20 MHz (typical 10
MHz). An input frequency detection circuit detects
the low frequency condition and, after applying a
>20-MHz input signal, this detection circuit turns the
PLL on and enables the outputs.
When AV_DD is strapped low, the PLL is turned off
and bypassed for test purposes. The CDCVF857 is
also able to track spread spectrum clocking for
reduced EMI.
Because the CDCVF857 is based on PLL circuitry, it
requires a stabilization time to achieve phase-lock of
the PLL. This stabilization time is required following
power up. The CDCVF857 is characterized for both
commercial and industrial temperature ranges.
A
A
AVAILABLE OPTIONS
T_A
–40°C to 85°C
–40°C to 85°C
TSSOP (DGG)
CDCVF857DGG
40-Pin MLF
CDCVF857RTB
CDCVF857RHA
56-Ball BGA⁽¹⁾
CDCVF857GQL
CDCVF857ZQL
(1) Maximum load recommended is 12 pf for 200 MHz. At 12-pf load, maximum T_A allowed is 70°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
MicroStar Junior is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2007, Texas Instruments Incorporated