CC1200 Datasheet, PDF (1/30 Pages) Texas Instruments – Low Power, High Performance RF Transceiver

CC1200
Low Power, High Performance RF Transceiver
Applications
Low power, high performance, wireless systems with
up to 1250 kbit/s data rate
169 / 433 / 868 / 915 / 920 MHz ISM/SRD bands
Possible support for additional frequency bands:
137 – 158.3, 205 – 237.5, and 274 – 316.6 MHz
Smart Metering (AMR/AMI)
Home and building automation
Wireless alarm and security systems
Industrial monitoring and control
Wireless healthcare applications
Wireless sensor networks and Active RFID
IEEE 802.15.4g applications
Wireless M-Bus, all modes
Regulations
Suitable for systems targeting compliance with:
Europe
US
Japan
ETSI EN 300 220, EN 54-25
FCC CFR47 Part 15
FCC CFR47 Part 90
ARIB STD-T30, T67, T108
Key Features
RF performance and analog features
High performance single chip transceiver
o Excellent receiver sensitivity:
-123 dBm at 1.2 kbps
-110 dBm at 50 kbps
o Blocking performance: 86 dB at 10 MHz
o Adjacent channel selectivity: up to 60 dB at
12.5 kHz offset
o Very low phase noise: -114 dBc/Hz at 10 kHz
offset (169 MHz)
Programmable output power up to +16 dBm with
0.4 dB step size
Automatic output power ramping
Supported modulation formats: 2-FSK, 2-GFSK,
4-FSK, 4-GFSK, MSK, OOK
Supports up to 1.25 Mbps data rate in transmit and
receive
Description
The CC1200 is a fully integrated single-chip radio
transceiver designed for high performance at very low
power and low voltage operation in cost effective wireless
systems. All filters are integrated, removing the need for
costly external SAW and IF filters. The device is mainly
intended for the ISM (Industrial, Scientific and Medical)
and SRD (Short Range Device) frequency bands at 164-
190 MHz, 410-475 MHz and 820-950 MHz.
The CC1200 provides extensive hardware support for
packet handling, data buffering, burst transmissions, clear
channel assessment, link quality indication and Wake-On-
Radio. The CC1200 main operating parameters can be
controlled via an SPI interface. In a typical system, the
CC1200 will be used together with a microcontroller and
only few external passive components.
The CC1200 and the CC1120 are both part of the high
performance transceiver family. The CC1120 is more
optimized towards narrowband applications, while the
Low current consumption:
Enhanced Wake-On-Radio functionality for automatic
low-power receive polling
Power down: 0.3 μA (0.5 μA with sleep timer active)
- RX: 2 mA in RX Sniff Mode
- RX: 19 mA peak current in low power mode
- RX: 23 mA peak current in high performance mode
- TX: 46 mA at +14 dBm
Digital features
WaveMatch: Advanced digital signal processing for
improved sync detect performance
Security: Hardware AES128 accelerator
Data FIFOs: Separate 128-byte RX and TX
Includes functions for antenna diversity support
Support for re-transmissions
Support for auto-acknowledge of received packets
Automatic Clear Channel Assessment (CCA) for listen-
before-talk (LBT) systems
Built in coding gain support for increased range and
robustness
Digital RSSI measurement
Support for seamless integration with the CC1190 for
increased range giving up to 3 dB improvement in RX
sensitivity and up to +27 dBm TX output power
Improved OOK shaping for less occupied bandwidth,
enabling higher output power whilst meeting regulatory
requirements
Dedicated packet handling for 802.15.4g
CRC 16/32
FEC, dual sync detection (FEC and non-FEC
packets)
Whitening
General
RoHS compliant 5x5mm QFN 32 package
Pin compatible with the CC1120
CC1200 is optimized towards wideband applications but can
also cover narrowband down to 12.5 kHz channels well.
VDD_GUARD 1
RESET_N 2
GPIO3 3
GPIO2 4
DVDD 5
DCPL 6
SI 7
SCLK 8
CC1200
GND
GROUND PAD
24 LPF1
23 LPF0
22 AVDD_SYNTH1
21 DCPL_VCO
20 LNA_N
19 LNA_P
18 TRX_SW
17 PA
PRODUCTION DATA information is current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty. Production processing does
not necessarily include testing of all parameters.
SWRS123B – REVISED JUNE 2013
Page 1 of 23