TSB43AB21 Datasheet, PDF (81/109 Pages) Texas Instruments – INTERGRATED 1394A-2000 OHCI PHY LINK-LAYER CONTROLLER

4.43 Isochronous Transmit Context Command Pointer Register
The isochronous transmit context command pointer register contains a pointer to the address of the first descriptor
block that the TSB43AB21 device accesses when software enables an isochronous transmit context by setting bit 15
(run) in the isochronous transmit context control register (see Section 4.42, Isochronous Transmit Context Control
Register) to 1. The isochronous transmit DMA context command pointer can be read when a context is active. The
n value in the following register addresses indicates the context number (n = 0, 1, 2, 3, …, 7).
Bit
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
Name
Isochronous transmit context command pointer
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
Name
Isochronous transmit context command pointer
Type
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Default X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Isochronous transmit context command pointer
20Ch + (16 * n)
Read-only
XXXX XXXXh
4.44 Isochronous Receive Context Control Register
The isochronous receive context control set/clear register controls options, state, and status for the isochronous
receive DMA contexts. The n value in the following register addresses indicates the context number (n = 0, 1, 2, 3).
See Table 4–34 for a complete description of the register contents.
Bit
Name
Type
Default
Bit
Name
Type
Default
31
30
29
28
27 26 25 24 23 22 21 20 19 18 17 16
Isochronous receive context control
RSC RSC RSCU RSC RSC R
R
R
R
R
R
R
R
R
R
R
X
X
X
X
X
0
0
0
0
0
0
0
0
0
0
0
15
14
13
12
11 10
9
8
7
6
5
4
3
2
1
0
Isochronous receive context control
RSCU R
R RSU RU RU R
R RU RU RU RU RU RU RU RU
0
0
0
X
0
0
0
0
X
X
X
X
X
X
X
X
Register:
Offset:
Type:
Default:
Isochronous receive context control
400h + (32 * n)
set register
404h + (32 * n)
clear register
Read/Set/Clear/Update, read/set/clear, read/set/update, read/update, read-only
XX00 X0XXh
Table 4–34. Isochronous Receive Context Control Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
bufferFill
RSC When bit 31 is set to 1, received packets are placed back-to-back to completely fill each receive
buffer. When this bit is cleared, each received packet is placed in a single buffer. If bit 28
(multiChanMode) is set to 1, this bit must also be set to 1. The value of this bit must not be changed
while bit 10 (active) or bit 15 (run) is set to 1.
30
isochHeader
RSC When bit 30 is set to 1, received isochronous packets include the complete 4-byte isochronous
packet header seen by the link layer. The end of the packet is marked with a xferStatus in the first
doublet, and a 16-bit timeStamp indicating the time of the most recently received (or sent) cycleStart
packet.
When this bit is cleared, the packet header is stripped from received isochronous packets. The
packet header, if received, immediately precedes the packet payload. The value of this bit must not
be changed while bit 10 (active) or bit 15 (run) is set to 1.
4–40