TL1051 Datasheet, PDF (6/13 Pages) Texas Instruments – VIDEO PREPROCESSOR CIRCUIT

TL1051
VIDEO PREPROCESSOR CIRCUIT
SOCS032B – NOVEMBER 1991
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)^†
Supply voltage, V_CC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V
Input voltage range, V_I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V
Operating free-air temperature range, T_A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 25°C to 75°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 125°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† _{Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and}
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to the GND terminal.
recommended operating conditions
Supply voltage, VCC
Input voltage, VI
High-level input voltage, VIH
Low-level input voltage, VIL
Operating free-air temperature, TA
RIN, GIN, BIN
WB
CLPLVLR, CLPLVLG, CLPLVLB
WCPCONT, AGCLMT, AGCCONT
AGCDET, AGCSET
CONTA, CONTB, SWR, SWG, SWB, PCL1,
PCL2, PBL, RESET
MIN NOM MAX UNIT
4.8
5 5.2 V
250
mV
0 3.05
5
2
V
0
3
5
3
3.5
V
0.4 V
– 20
45 °C
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
all sections
PARAMETER
ICC Supply current
Y-switch section
PARAMETER
White-clip level (see Note 2)
Gate-pulse impedance
Gate-pulse capacitance
SWB, SWG,
SWR
TEST CONDITIONS
VCC = 5 V
TEST CONDITIONS
MIN TYP‡ MAX UNIT
40
50 mA
MIN
400%
TYP‡
5
MAX
10
UNIT
kΩ
pF
clamp section
PARAMETER
Clamp-pulse current
Clamp resistance
Clamp-pulse input capacitance
Noise rejection
‡ _{All typical values are at TA = 25° C.}
NOTE 2: 250 mV = 100%.
PCL1
BIN, GIN, RIN
PCL1
PCL1 to YSW
TEST CONDITIONS
PCL1 = 1 µs
MIN
– 0.2
TYP‡
30
30
MAX
0.2
30
UNIT
mA
Ω
pF
dB
4-6
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265