CD54HC4051_07 Datasheet, PDF (6/30 Pages) Texas Instruments – High-Speed CMOS Logic Analog Multiplexers/Demultiplexers

’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053
Absolute Maximum Ratings (Note 2)
Thermal Information
DC Supply Voltage, V_CC - V_EE . . . . . . . . . . . . . . . . . -0.5V to 10.5V
DC Supply Voltage, V_{CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7V}
DC Supply Voltage, V_{EE . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.5V to -7V}
DC Input Diode Current, I_IK
For V_I < -0.5V or V_I > V_CC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA
DC Switch Diode Current, I_OK
For V_I < V_EE -0.5V or V_I > V_CC + 0.5V . . . . . . . . . . . . . . . . .±20mA
DC Switch Current, (Note 2)
For V_I > V_EE -0.5V or V_I < V_CC + 0.5V . . . . . . . . . . . . . . . . .±25mA
DC V_CC or Ground Current, I_CC . . . . . . . . . . . . . . . . . . . . . . . . .±50mA
DC V_EE Current, I_EE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20mA
NOTE:
Package Thermal Impedance, θ_JA (see Note 1):
E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67^oC/W
M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73^oC/W
NS (SOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64^oC/W
PW (TSSOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . 108^oC/W
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150^oC
Maximum Storage Temperature Range . . . . . . . . . .-65^oC to 150^oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300^oC
1. The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions For maximum reliability, nominal operating conditions should be selected so that
operation is always within the following ranges
PARAMETER
MIN
MAX
UNITS
Supply Voltage Range (For T_A = Full Package Temperature Range), V_CC (Note 2)
CD54/74HC Types
2
6
V
CD54/74HCT Types
4.5
5.5
V
Supply Voltage Range (For T_A = Full Package Temperature Range), V_CC - V_EE
CD54/74HC Types, CD54/74HCT Types (See Figure 1)
2
10
V
Supply Voltage Range (For T_A = Full Package Temperature Range), V_EE (Note 3)
CD54/74HC Types, CD54/74HCT Types (See Figure 2)
0
-6
V
DC Input Control Voltage, V_I
Analog Switch I/O Voltage, V_IS
Operating Temperature, T_A
Input Rise and Fall Times, t_r, t_f
2V
GND
V_CC
V
V_EE
V_CC
V
-55
125
o_C
0
1000
ns
4.5V
0
500
ns
6V
0
400
ns
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. All voltages referenced to GND unless otherwise specified..
3. In certain applications, the external load resistor current may include both V_CC and signal line components. To avoid drawing V_CC current
when switch current flows into the transmission gate inputs, the voltage drop across the bidirectional switch must not exceed 0.6V (cal-
culated from r_ON values shown in Electrical Specifications table). No V_CC current will flow through R_L if the switch current flows into
terminal 3 on the HC/HCT4051; terminals 3 and 13 on the HC/HCT4052; terminals 4, 14 and 15 on the HC/HCT4053.
Recommended Operating Area as a Function of Supply Voltages
8
6
4 HC
HCT
2
0
0 2 4 6 8 10 12
V_CC - V_EE (V)
FIGURE 1.
8
6
HCT
4
HC
2
0
0 -2 -4 -6 -8
V_EE - GND (V)
FIGURE 2.
6