THS4521_10 Datasheet, PDF (5/48 Pages) Texas Instruments – VERY LOW POWER, NEGATIVE RAIL INPUT, RAIL-TO-RAIL OUTPUT, FULLY DIFFERENTIAL AMPLIFIER

www.ti.com
THS4521
THS4522
THS4524
SBOS458D – DECEMBER 2008 – REVISED AUGUST 2010
ELECTRICAL CHARACTERISTICS: V_S+ – V_S– = 5 V
At V_S+ = +5 V, V_S– = 0 V, V_OCM = open, V_OUT = 2 V_PP (differential), R_F = 1 kΩ, R_L = 1 kΩ differential, G = 1 V/V, single-ended
input, differential output, input and output referenced to midsupply, unless otherwise noted.
PARAMETER
CONDITIONS
THS4521, THS4522, THS4524
MIN
TYP
MAX
UNIT
TEST
LEVEL ⁽¹⁾
AC PERFORMANCE
Small-Signal Bandwidth
Gain Bandwidth Product
Large-Signal Bandwidth
Bandwidth for 0.1-dB Flatness
Rising Slew Rate (Differential)
Falling Slew Rate (Differential)
Overshoot
Undershoot
Rise Time
Fall Time
Settling Time to 1%
Harmonic Distortion
2nd harmonic
V_OUT = 100 mV_PP, G = 1
V_OUT = 100 mV_PP, G = 2
V_OUT = 100 mV_PP, G = 5
V_OUT = 100 mV_PP, G = 10
V_OUT = 100 mV_PP, G = 10
V_OUT = 2 V_PP, G = 1
V_OUT = 2 V_PP, G = 1
V_OUT = 2-V Step, G = 1, R_L = 200 Ω
V_OUT = 2-V Step, G = 1, R_L = 200 Ω
V_OUT = 2-V Step, G = 1, R_L = 200 Ω
V_OUT = 2-V Step, G = 1, R_L = 200 Ω
V_OUT = 2-V Step, G = 1, R_L = 200 Ω
V_OUT = 2-V Step, G = 1, R_L = 200 Ω
V_OUT = 2-V Step, G = 1, R_L = 200 Ω
f = 1 kHz, V_OUT = 1 V_RMS, G = 1⁽²⁾,
differential input
145
50
20
9.5
95
145
30
490
600
1
2.6
3.4
3
10
–122
MHz
C
MHz
C
MHz
C
MHz
C
MHz
C
MHz
C
MHz
C
V/ms
C
V/ms
C
%
C
%
C
ns
C
ns
C
ns
C
dBc
C
3rd harmonic
f = 1 MHz, V_OUT = 2 V_PP, G = 1
f = 1 kHz, V_OUT = 1 V_RMS, G = 1⁽²⁾,
differential input
–85
–141
dBc
C
dBc
C
Second-Order Intermodulation Distortion
Third-Order Intermodulation Distortion
Input Voltage Noise
f = 1 MHz, V_OUT = 2 V_PP, G = 1
Two-tone, f₁ = 2 MHz, f₂ = 2.2 MHz,
V_OUT = 2-V_PP envelope
Two-tone, f₁ = 2 MHz, f₂ = 2.2 MHz,
V_OUT = 2-V_PP envelope
f > 10 kHz
–91
dBc
C
–86
dBc
C
–93
dBc
C
4.6
nV/√Hz
C
Input Current Noise
f > 100 kHz
0.6
pA/√Hz
C
SNR
V_OUT = 5 V_PP, 20 Hz to 22 kHz BW,
differential input
114
dBc
C
THD+N
f = 1 kHz , V_OUT = 5 V_PP, 20 Hz to 22 kHz
BW, differential input
112
dBc
C
Overdrive Recovery Time
Overdrive = ±0.5 V
75
ns
C
Output Balance Error
Closed-Loop Output Impedance
V_OUT = 100 mV, f < 2 MHz, V_IN differential
–57
f = 1 MHz (differential)
0.3
dB
C
Ω
C
Channel-to-Channel Crosstalk (THS4522. THS4524)
f = 10 kHz, measured differentially
–125
dB
C
DC PERFORMANCE
Open-Loop Voltage Gain (A_OL)
Input-Referred Offset Voltage
Input offset voltage drift⁽³⁾
Input Bias Current
Input bias current drift⁽³⁾
Input Offset Current
T_A = +25°C
T_A = –40°C to +85°C
T_A = –40°C to +85°C
T_A = +25°C
T_A = –40°C to +85°C
T_A = –40°C to +85°C
T_A = +25°C
100
119
dB
A
±0.24
±2
mV
A
±0.5
±3.5
mV
B
±2
mV/°C
B
0.7
0.9
mA
B
0.9
1.1
mA
B
±1.8
±2.2
nA/°C
B
±50
±60
pA
B
(1) Test levels: (A) 100% tested at +25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization
and simulation. (C) Typical value only for information.
(2) Not directly measureable; calculated using noise gain of 101 as described in the Applications section, Audio Performance.
(3) Input Offset Voltage Drift, Input Bias Current Drift, and Input Offset Current Drift are average values calculated by taking data at –40°C
and +85°C, computing the difference, and dividing by 125.
Copyright © 2008–2010, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): THS4521 THS4522 THS4524