SN74CBT3384C Datasheet, PDF (5/15 Pages) Texas Instruments – 10-BIT FET BUSSWITCH 5-V BUS SWITCH WITH -2-V UNDERSHOOT PROTECTION

SN74CBT3384C
10ĆBIT FET BUS SWITCH
5ĆV BUS SWITCH WITH ć2ĆV UNDERSHOOT PROTECTION
SCDS132A − SEPTEMBER 2003 − REVISED OCTOBER 2003
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN TYP† MAX UNIT
VIK
Control inputs VCC = 4.5 V,
IIN = −18 mA
−1.8 V
VIKU
Data inputs
VCC = 5 V,
0 mA > II ≥ −50 mA,
VIN = VCC or GND,
Switch OFF
−2 V
IIN
IOZ‡
Control inputs VCC = 5.5 V,
VCC = 5.5 V,
VIN = VCC or GND
VO = 0 to 5.5 V,
VI = 0,
Switch OFF,
VIN = VCC or GND
±1 µA
±10 µA
Ioff
VCC = 0,
VO = 0 to 5.5 V,
VI = 0
10 µA
ICC
∆ICC§
VCC = 5.5 V,
Control inputs VCC = 5.5 V,
II/O = 0,
VIN = VCC or GND,
One input at 3.4 V,
Switch ON or OFF
Other inputs at VCC or GND
3 µA
2.5 mA
Cin
Control inputs VIN = 3 V or 0
3.5
pF
Cio(OFF)
VI/O = 3 V or 0,
Switch OFF,
VIN = VCC or GND
5
pF
Cio(ON)
VI/O = 3 V or 0,
Switch ON,
VIN = VCC or GND
12.5
pF
VCC = 4 V,
TYP at VCC = 4 V
VI = 2.4 V,
IO = −15 mA
8
12
ron¶
VCC = 4.5 V
VI = 0
IO = 64 mA
IO = 30 mA
3
6Ω
3
6
VI = 2.4 V,
IO = −15 mA
5
10
VIN and IIN refer to control inputs. VI, VO, II, and IO refer to data pins.
† _{All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C.}
‡ _{For I/O ports, the parameter IOZ includes the input leakage current.}
§ _{This is the increase in supply current for each input that is at the specified voltage level, rather than VCC or GND.}
¶ _{Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is determined by}
the lower of the voltages of the two (A or B) terminals.
switching characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Figure 3)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
VCC = 4 V
MIN MAX
VCC = 5 V
± 0.5 V
MIN MAX
UNIT
tpd#
A or B
B or A
0.24
0.15 ns
ten
OE
A or B
5 1.5 4.2 ns
tdis
OE
A or B
5 1.5 4.5 ns
# _{The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance,}
when driven by an ideal voltage source (zero output impedance).
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
5