MLM324P Datasheet, PDF (5/31 Pages) Texas Instruments – LM124-N/LM224-N/LM324-N/LM2902-N Low Power Quad Operational Amplifiers

LM124-N, LM224-N, LM2902-N, LM324-N
www.ti.com
SNOSC16B – MAY 2004 – REVISED SEPTEMBER 2004
ELECTRICAL CHARACTERISTICS (continued)
V⁺ = +5.0V, ⁽¹⁾, unless otherwise stated
Parameter
Conditions
Large Signal
Voltage Gain
Output Voltage
Swing
Output Current
V_OH
V_OL
Source
Sink
V⁺ = +15V (V_OSwing = 1V to 11V)
R_L ≥ 2 kΩ
V⁺ = 30V
(LM2902-N, V⁺ = 26V)
V⁺ = 5V, R_L = 10 kΩ
V_O = 2V
R_L = 2 kΩ
R_L = 10 kΩ
V_IN+ = +1V,
V_IN^− = 0V,
V⁺ = 15V
V_IN^− = +1V,
V_IN+ = 0V,
V⁺ = 15V
LM124A
LM224A
LM324A
Min Typ Max Min Typ Max Min Typ Max
25
25
15
26
26
26
27 28
27 28
27 28
5 20
5 20
5
20
10 20
10 20
10 20
10 15
58
58
Units
V/mV
V
mV
mA
ELECTRICAL CHARACTERISTICS
V⁺ = +5.0V, ⁽¹⁾, unless otherwise stated
Parameter
Input Offset Voltage
Input Bias Current⁽³⁾
Input Offset Current
Input Common-Mode
Voltage Range⁽⁴⁾
Supply Current
Large Signal
Voltage Gain
Common-Mode
Rejection Ratio
Power Supply
Rejection Ratio
Amplifier-to-Amplifier
Coupling ⁽⁵⁾
Conditions
T_A = 25°C⁽²⁾
I_IN(+) or I_IN(−), V_CM = 0V,
T_A = 25°C
I_IN(+) or I_IN(−), V_CM = 0V,
T_A = 25°C
V⁺ = 30V, (LM2902-N, V⁺ = 26V),
T_A = 25°C
Over Full Temperature Range
R_L = ∞ On All Op Amps
V⁺ = 30V (LM2902-N V⁺ = 26V)
V⁺ = 5V
V⁺ = 15V, R_L≥ 2kΩ,
(V_O = 1V to 11V), T_A = 25°C
DC, V_CM = 0V to V⁺ − 1.5V,
T_A = 25°C
V⁺ = 5V to 30V
(LM2902-N, V⁺ = 5V to 26V),
T_A = 25°C
f = 1 kHz to 20 kHz, T_A = 25°C
(Input Referred)
LM124-N/LM224-N
LM324-N
LM2902-N
Min Typ Max Min Typ Max Min Typ Max
2
5
2
7
2
7
Units
mV
45 150
45 250
45 250
nA
3
30
5 50
5 50
nA
0
V⁺−1.5 0
V⁺−1.5 0
V⁺−1.5
V
1.5 3
1.5 3
1.5 3
0.7 1.2
0.7 1.2
0.7 1.2
50 100
25 100
25 100
mA
V/mV
70 85
65 85
50 70
dB
65 100
65 100
50 100
dB
−120
−120
−120
dB
(1) These specifications are limited to −55°C ≤ T_A ≤ +125°C for the LM124-N/LM124A. With the LM224-N/LM224A, all temperature
specifications are limited to −25°C ≤ T_A ≤ +85°C, the LM324-N/LM324A temperature specifications are limited to 0°C ≤ T_A ≤ +70°C, and
the LM2902-N specifications are limited to −40°C ≤ T_A ≤ +85°C.
(2) V_O ≃ 1.4V, R_S = 0Ω with V⁺ from 5V to 30V; and over the full input common-mode range (0V to V⁺ − 1.5V) for LM2902-N, V⁺ from 5V to
26V.
(3) The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the
state of the output so no loading change exists on the input lines.
(4) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25°C). The
upper end of the common-mode voltage range is V⁺ − 1.5V (at 25°C), but either or both inputs can go to +32V without damage (+26V
for LM2902-N), independent of the magnitude of V⁺.
(5) Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This
typically can be detected as this type of capacitance increases at higher frequencies.
Copyright © 2004, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM124-N LM224-N LM2902-N LM324-N