OPA2674 Datasheet, PDF (4/33 Pages) Burr-Brown (TI) – Dual Wideband, High Output Current Operational Amplifier with Current Limit

OPA2674
SBOS270A − AUGUST 2003 − REVISED MAY 2006
www.ti.com
ELECTRICAL CHARACTERISTICS: V_S = ±6V (continued)
Boldface limits are tested at +25°C.
At T_A = +25°C, A₁ = A₀ = 1 (full power: for SO-14 only), G = +4, R_F = 402Ω, and R_L = 100Ω, unless otherwise noted. See Figure 1 for AC performance only.
OPA2674ID, OPA2674I-14D
PARAMETER
Power Supply
Specified Operating Voltage
Maximum Operating Voltage
Maximum Quiescent Current
Minimum Quiescent Current
Power-Supply Rejection Ratio (PSRR)
Power Supply (SO-14 Only)
Maximum Logic 0
Minimum Logic 1
Logic Input Current
Supply Current at Full Power
Supply Current at Power Cutback
Supply Current at Idle Power
Supply Current at Shutdown
Output Impedance in Idle Power
Output Impedance in Shutdown
Supply Current Step Time
Output Switching Glitch
Shutdown Isolation
Thermal Characteristics
Specification: ID, I-14D
Thermal Resistance, q_JA
ID
SO-8
I-14D SO-14
TEST CONDITIONS
TYP
+25°C
MIN/MAX OVER TEMPERATURE
0°C to −40°C to
+25°C(1) +70°C(2) +85°C(2) UNITS
MIN/
MAX
TEST
LEVEL
(3)
±6
V
typ
C
±6.3
±6.3
±6.3
V
max
A
VS = ±6V
18
18.6
18.8
19.2
mA max
A
VS = ±6V
18
17.4
16.5
16.0
mA
min
A
f = 100kHz, Input-Referred
56
51
49
48
dB
min
A
A1, A0, +VS = +6V
2.5
2.0
1.8
1.5
V
max
A
A1, A0, +VS = +6V
3.3
3.6
4.0
4.2
V
min
A
A1 = 0V, A0 = 0V, Each Line
60
90
100
105
µA
max
A
A1 = 1, A0 = 1 (logic levels)
18.0
18.6
18.8
19.2
mA max
A
A1 = 1, A0 = 0 (logic levels)
13.3
14.2
14.4
14.8
mA max
A
A1 = 0, A0 = 1 (logic levels)
4.0
4.8
5.1
5.3
mA max
A
A1 = 0, A0 = 0 (logic levels)
1.0
1.3
1.4
1.5
mA max
A
G = +4, f < 1MHz
0.1
Ω
typ
C
100 4
kΩ pF typ
C
10% to 90% Change
200
ns
typ
C
Inputs at GND
±20
mV
typ
C
G = +4, 1MHz, A1 = 0, A0 = 0
85
dB
typ
C
Junction-to-Ambient
−40 to
+85
125
100
°C
°C/W typ
C
°C/W typ
C
(1) _{Junction temperature = ambient for +25°C specifications.}
(2) _{Junction temperature = ambient at low temperature limit; junction temperature = ambient +23°C at high temperature limit for over temperature}
specifications.
(3) _{Test levels: (A) 100% tested at +25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and}
simulation. (C) Typical value only for information.
(4) _{Current is considered positive out of node. VCM is the input common-mode voltage.}
(5) _{Tested < 3dB below minimum CMRR specification at ± CMIR limits.}
4