LM109JAN_15 Datasheet, PDF (4/13 Pages) Texas Instruments – LM109JAN 5-Volt Regulator

LM109JAN
SNVS379B – NOVEMBER 2005 – REVISED MARCH 2013
OBSOLETE
www.ti.com
JL109H Electrical Characteristics DC Parameters
Symbol
Parameter
Conditions
Notes Min Max
V_O
Output Voltage
V_RLine
Line Regulation
V_I = 7V, I_L = -5mA
V_I = 7V, I_L = -0.5A
V_I = 9V, I_L = -0.5A
V_I = 25V, I_L = -5mA
V_I = 25V, I_L = -100mA
7V ≤ V_I ≤ 25V, I_L = -5mA
V_RLoad
I_SCD
ΔI_SCD
(Line)
ΔI_SCD
(Load)
I_OS
V_Start
ΔV_O / ΔT
Load Regulation
Standby Current Drain
Standby Current Drain vs Line
Voltage
Standby Current Drain vs Load
Current
Output Short Circuit Current
Minimum Start Up Input Voltage
V_I = 10V, -0.5A ≤ I_L ≤ -5mA
V_I = 7V, I_L = -5mA
V_I = 25V, I_L = -5mA
7V ≤ V_I ≤ 25V, I_L = -5mA
V_I = 10V, -0.5A ≤ I_L ≤ -5mA
V_I = 35V
R_L = 25Ω ±5%
Average Temperature Coefficient V_I = 7V, I_L = -5mA
of Output Voltage
4.7 5.4
(1)
4.7 5.4
4.7 5.4
4.7 5.4
4.7 5.4
-50 50
-100 100
-100 100
-10 0.5
-10 0.5
-0.5 0.5
-0.8 0.8
-2.0 0.01
(2) (3)
9.0
(4)
-2.0 2.0
(1) V_I = 8V at −55°C.
(2) This test is performed by shifting the input voltage in 50mV increments until output reaches 4.706V.
(3) Parameter tested go-no-go, only.
(4) Calculated parameter.
Unit
V
V
V
V
V
mV
mV
mV
mA
mA
mA
mA
A
V
mV/°C
Sub-
groups
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1
2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
8A, 8B
JL109H Electrical Characteristics AC Parameters
Symbol
Parameter
Conditions
N_O
ΔV_O / ΔV_I
ΔV_O / ΔI_L
ΔV_I / ΔV_O
Output Noise Voltage
Line Transient Response
Load Transient Response
Ripple Rejection
V_I = 10V, I_L = -50mA
V_I = 10V, V_Pulse = 3V,
I_L = -5mA
V_I = 10V, I_L = -50mA,
ΔI_L = -200mA
V_I = 10V, I_L = -125mA,
e_I = 1V_RMS at ƒ = 2400Hz
(1) Slash Sheet limit of 15 mV/V is equivalent to 45mV
(2) Slash Sheet limit of 2mV/mA is equivalent to 400mV
Notes
(1)
(2)
Min Max
125
45
400
60
Unit
µV_RMS
mV
mV
dB
Sub-
groups
7
7
7
4
JL109H Electrical Characteristics DC Drift Parameters
Delta calculations performed on JAN S devices at group B, Subgroup 5, only.
Symbol
Parameter
Conditions
Notes
Min
Max
Unit
Sub-
groups
V_O
Output Voltage
V_RLine
V_RLoad
I_SCD
Line Regulation
Load Regulation
V_I = 7V, I_L = -5mA
V_I = 7V, I_L = -0.5A
V_I = 9V, I_L = -0.5A
V_I = 25V, I_L = -5mA
V_I = 25V, I_L = -100mA
7V ≤ V_I ≤ 25V, I_L = -5mA
V_I = 10V, -0.5A ≤ I_L ≤ -5mA
V_I = 7V, I_L = -5mA
V_I = 25V, I_L = -5mA
-0.025 0.025
V
1
-0.025 0.025
V
1
-0.025 0.025
V
1
-0.025 0.025
V
1
-0.025 0.025
V
1
-10
10
mV
1
-10
10
mV
1
-1.0
1.0
mA
1
-1.0
1.0
mA
1
4
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated