TL4581_06 Datasheet, PDF (3/8 Pages) Texas Instruments – DUAL LOW-NOISE HIGH-DRIVE OPERATIONAL AMPLIFIER

TL4581
DUAL LOW-NOISE HIGH-DRIVE OPERATIONAL AMPLIFIER
SLVS457A – JANUARY 2003 – REVISED MARCH 2003
electrical characteristics, V_CC± = +15 V, T_A = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS^†
MIN TYP MAX
VIO
IIO
IIB
VICR
VOPP
AVD
Avd
Input offset voltage
Input offset current
Input bias current
Common-mode input-voltage range
Maximum peak-to-peak
output-voltage swing
Large-signal
differential-voltage amplification
Small-signal
differential-voltage amplification
VO = 0
TA = 25°C
TA = 0°C to 70°C
TA = 25°C
TA = 0°C to 70°C
TA = 25°C
TA = 0°C to 70°C
RL ≥ 600 Ω
RL ≥ 600 Ω,
VO = ±10 V
RL ≥ 2 kΩ,
VO = ±10 V
f = 10 kHz
VCC_± = ±15 V
VCC_± = ±18 V
TA = 25°C
TA = 0°C to 70°C
TA = 25°C
TA = 0°C to 70°C
0.5
4
5
10 150
200
200 800
1000
±12 ±13
24
26
30
32
15
50
10
25 100
15
2.2
BOM Maximum-output-swing bandwidth
B1
ri
zo
CMRR
kSVR
IOS
ICC
Unity-gain bandwidth
Input resistance
Output impedance
Common-mode rejection ratio
Supply-voltage rejection ratio
(∆VCC_±/∆VIO)
Output short-circuit current
Total supply curent
Crosstalk attenuation (VO1/VO2)
RL = 600 Ω
RL = 600 Ω,
VO = ±10 V
VCC_± = ±18 V,
CL = 100 pF
AVD = 30 dB,
VIC = VICR min
RL = 600 Ω,
VCC_± = ±9 V to ±15 V,
VO = 0,
V01 = 10 V
peak,
No load
f = 1 kHz
VO = ±14 V
f = 10 kHz
VO = 0
140
100
10
30 300
0.3
70 100
80 100
10
38
60
8
16
110
† _{All characteristics are measured under open-loop conditions with zero common-mode input voltage, unless otherwise specified.}
UNIT
mV
nA
nA
V
V
V/mV
V/mV
kHz
MHz
kΩ
Ω
dB
dB
mA
mA
dB
operating characteristics, V_CC± = ±15 V, T_A = 25°C
PARAMETER
TEST CONDITIONS
SR Slew rate at unity gain
Overshoot factor
Vn
Equivalent input noise voltage
VI = 100 mV,
RL = 600 Ω,
f = 30 Hz
f = 1 kHz
In
Equivalent input noise current
f = 30 Hz
f = 1 kHz
AVD = 1,
CL = 100 pF
MIN TYP MAX UNIT
9
V/µs
10
%
8
nV/√Hz
5
2.7
pA/√Hz
0.7
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
3