SN74AUC1G74_10 Datasheet, PDF (3/16 Pages) Texas Instruments – SINGLE POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOP WITH CLEAR AND PRESET

www.ti.com
SN74AUC1G74
SINGLE POSITIVE-EDGE-TRIGGERED D-TYPE FLIP-FLOP
WITH CLEAR AND PRESET
SCES537D – DECEMBER 2003 – REVISED JUNE 2007
Absolute Maximum Ratings⁽¹⁾
over operating free-air temperature range (unless otherwise noted)
V_CC Supply voltage range
V_I
Input voltage range⁽²⁾
V_O
Voltage range applied to any output in the high-impedance or power-off state⁽²⁾
V_O
Output voltage range⁽²⁾
I_IK
Input clamp current
V_I < 0
I_OK Output clamp current
V_O < 0
I_O
Continuous output current
Continuous current through V_CC or GND
DCT package
θ_JA
Package thermal impedance⁽³⁾
DCU package
RSE package
YZP/YZT package
T_stg Storage temperature range
MIN
MAX
–0.5
3.6
–0.5
3.6
–0.5
3.6
–0.5 V_CC + 0.5
–50
–50
±20
±100
220
227
253
102
–65
150
UNIT
V
V
V
V
mA
mA
mA
mA
°C/W
°C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
(3) The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions⁽¹⁾
V_CC
Supply voltage
V_IH
High-level input voltage
V_IL
Low-level input voltage
V_I
Input voltage
V_O
Output voltage
I_OH
High-level output current
I_OL
Low-level output current
Δt/Δv Input transition rise or fall rate
T_A
Operating free-air temperature
V_CC = 0.8 V
V_CC = 1.1 V to 1.95 V
V_CC = 2.3 V to 2.7 V
V_CC = 0.8 V
V_CC = 1.1 V to 1.95 V
V_CC = 2.3 V to 2.7 V
V_CC = 0.8 V
V_CC = 1.1 V
V_CC = 1.4 V
V_CC = 1.65 V
V_CC = 2.3 V
V_CC = 0.8 V
V_CC = 1.1 V
V_CC = 1.4 V
V_CC = 1.65 V
V_CC = 2.3 V
V_CC = 0.8 V to 1.65 V⁽²⁾
V_CC = 1.65 V to 2.3 V⁽³⁾
V_CC = 2.3 V to 2.7 V⁽³⁾
MIN
0.8
V_CC
0.65 × V_CC
1.7
0
0
–40
MAX
2.7
0
0.35 × V_CC
0.7
3.6
V_CC
–0.7
–3
–5
–8
–9
0.7
3
5
8
9
20
20
20
85
UNIT
V
V
V
V
V
mA
mA
ns/V
°C
(1) All unused inputs of the device must be held at V_CC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
(2) The data was taken at C_L = 15 pF, R_L = 2 kΩ (see Figure 1).
(3) The data was taken at C_L = 30 pF, R_L = 500 Ω (see Figure 1).
Submit Documentation Feedback
3