OPA27CZ Datasheet, PDF (3/22 Pages) Texas Instruments – Ultra-Low Noise, Precision OPERATIONAL AMPLIFIERS

ELECTRICAL CHARACTERISTICS
At V_CC = ±15V and T_A = +25°C, unless otherwise noted.
PARAMETER
INPUT NOISE ⁽⁶⁾
Voltage, f_O = 10Hz
f_O = 30Hz
f_O = 1kHz
f_B = 0.1Hz to 10Hz
Current,⁽¹⁾ f_O = 10Hz
f_O = 30Hz
f_O = 1kHz
OFFSET VOLTAGE ⁽²⁾
Input Offset Voltage
Average Drift ⁽³⁾
Long Term Stability ⁽⁴⁾
CONDITIONS
T_{A MIN} to T_{A MAX}
OPA27
OPA37
MIN
TYP
MAX
UNITS
3.8
8.0
nV/√Hz
3.3
5.6
nV/√Hz
3.2
4.5
nV/√Hz
0.09
1.7
0.25
µV_PP
pA/√Hz
1.0
pA/√Hz
0.4
0.6
pA/√Hz
±25
±100
µV
±0.4
±1.8 ⁽⁶⁾
µV/°C
0.4
2.0
µV/mo
Supply Rejection
BIAS CURRENT
Input Bias Current
OFFSET CURRENT
Input Offset Current
IMPEDANCE
Common-Mode
VOLTAGE RANGE
Common-Mode Input Range
Common-Mode Rejection
OPEN-LOOP VOLTAGE GAIN, DC
FREQUENCY RESPONSE
Gain-Bandwidth Product⁽⁵⁾
Slew Rate ⁽⁵⁾
Settling Time, 0.01%
RATED OUTPUT
Voltage Output
Output Resistance
Short Circuit Current
POWER SUPPLY
Rated Voltage
Voltage Range,
Derated Performance
Current, Quiescent
TEMPERATURE RANGE
Specification
Operating
±V_CC = 4 to 18V
±V_CC = 4 to 18V
V_IN = ±11VDC
R_L ≥ 2kΩ
R_L ≥ 1kΩ
OPA27
OPA37
V_O = ±10V,
R_L = 2kΩ
OPA27, G = +1
OPA37, G = +5
OPA27, G = +1
OPA37, G = +5
R_L ≥ 2kΩ
R_L ≥ 600Ω
DC, Open Loop
R_L = 0Ω
I_O = 0mADC
94
±11
100
117
5 ⁽⁶⁾
45 ⁽⁶⁾
1.7 ⁽⁶⁾
11⁽⁶⁾
±12
±10
±4
–40
–40
120
±1
±15
10
2 || 2.5
±12.3
122
124
124
8
63
1.9
11.9
25
25
±13.8
±12.8
70
25
±15
3.3
±20
±80
75
60⁽⁶⁾
±22
5.7
+85
+85
dB
µV/V
nA
nA
GΩ || pF
V
dB
dB
dB
MHz
MHz
V/µs
V/µs
µs
µs
V
V
Ω
mA
VDC
VDC
mA
°C
°C
NOTES: (1) Measured with industry-standard noise test circuit (Figures 1 and 2). Due to errors introduced by this method, these current noise specifications should
be used for comparison purposes only. (2) Offset voltage specification are measured with automatic test equipment after approximately 0.5 seconds from power turn-
on. (3) Unnulled or nulled with 8kΩ to 20kΩ potentiometer. (4) Long-term voltage offset vs time trend line does not include warm-up drift. (5) Typical specification only
on plastic package units. Slew rate varies on all units due to differing test methods. Minimum specification applies to open-loop test. (6) This parameter specified by
design.
OPA27, OPA37
3
SBOS135C
www.ti.com