AD8002ANZ Datasheet, PDF (3/21 Pages) Analog Devices – Dual 600 MHz, 50 mW Current Feedback Amplifier

AD8002–SPECIFICATIONS ^{(@ T}A ^{= 25؇C, V}S ^{= ؎5 V, R}L ^{= 100 ⍀, R}C1 ^{= 75 ⍀, unless otherwise noted.)}
Model
Conditions
AD8002A
Min Typ Max
Unit
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth, N Package
R Package
RM Package
Bandwidth for 0.1 dB Flatness
Slew Rate
N Package
R Package
RM Package
Settling Time to 0.1%
Rise and Fall Time
NOISE/HARMONIC PERFORMANCE
Total Harmonic Distortion
Crosstalk, Output to Output
Input Voltage Noise
Input Current Noise
Differential Gain Error
Differential Phase Error
Third Order Intercept
1 dB Gain Compression
SFDR
G = +2, R_F = 750 Ω
G = +1, R_F = 1.21 kΩ
G = +2, R_F = 681 Ω
G = +1, R_F = 953 Ω
G = +2, R_F = 681 Ω
G = +1, R_F = 1 kΩ
G = +2, R_F = 750 Ω
G = +2, R_F = 681 Ω
G = +2, R_F = 681 Ω
G = +2, V_O = 2 V Step
G = –1, V_O = 2 V Step
G = +2, V_O = 2 V Step
G = +2, V_O = 2 V Step, R_F = 750 Ω
f_C = 5 MHz, V_O = 2 V p-p
G = +2, R_L = 100 Ω
f = 5 MHz, G = +2
f = 10 kHz, R_C = 0 Ω
f = 10 kHz, +In
–In
NTSC, G = +2, R_L = 150 Ω
NTSC, G = +2, R_L = 150 Ω
f = 10 MHz
f = 10 MHz
f = 5 MHz
500
600
500
600
500
600
60
90
60
700
1200
16
2.4
–65
–60
2.0
2.0
18
0.01
0.02
33
14
–66
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
V/µs
V/µs
ns
ns
dBc
dB
nV/√Hz
pA/√Hz
pA/√Hz
%
Degree
dBm
dBm
dB
DC PERFORMANCE
Input Offset Voltage
Offset Drift
–Input Bias Current
+Input Bias Current
Open Loop Transresistance
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
Offset Voltage
–Input Current
+Input Current
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current²
Short Circuit Current²
T_MIN–T_MAX
T_MIN–T_MAX
T_MIN–T_MAX
V_O = ± 2.5 V
T_MIN–T_MAX
+Input
–Input
+Input
V_CM = ± 2.5 V
V_CM = ± 2.5 V, T_MIN–T_MAX
V_CM = ± 2.5 V, T_MIN–T_MAX
R_L = 150 Ω
2.0
6
2.0
9
10
5.0
25
35
3.0
6.0
10
250
900
175
10
50
1.5
3.2
49
54
0.3
1.0
0.2
0.9
2.7
3.1
70
85
110
mV
mV
µV/°C
±µA
±µA
±µA
±µA
kΩ
kΩ
MΩ
Ω
pF
±V
dB
µA/V
µA/V
±V
mA
mA
POWER SUPPLY
Operating Range
Quiescent Current/Both Amplifiers
Power Supply Rejection Ratio
–Input Current
+Input Current
T_MIN–T_MAX
+V_S = +4 V to +6 V, –V_S = –5 V
–V_S = – 4 V to – 6 V, +V_S = +5 V
T_MIN–T_MAX
T_MIN–T_MAX
± 3.0
10.0
60
75
49
56
0.5
0.1
NOTES
1_{RC is recommended to reduce peaking and minimize input reflections at frequencies above 300 MHz. However, R C is not required.}
2_{Output current is limited by the maximum power dissipation in the package. See the power derating curves.}
Specifications subject to change without notice.
± 6.0
11.5
2.5
0.5
V
mA
dB
dB
µA/V
µA/V
–2–
REV. D