CD54ACT05 Datasheet, PDF (2/8 Pages) Texas Instruments – HEX INVERTERS WITH OPEN-DRAIN OUTPUTS

CD54ACT05, CD74ACT05
HEX INVERTERS
WITH OPEN-DRAIN OUTPUTS
SCHS311C – JANUARY 2001 – REVISED JANUARY 2007
Absolute Maximum Ratings⁽¹⁾
over operating free-air temperature range (unless otherwise noted)
www.ti.com
V_CC Supply voltage range
I_IK
Input clamp current⁽²⁾
I_OK
Output clamp current⁽²⁾
I_O
Continuous current
θ_JA
Package thermal impedance⁽³⁾
T_stg Storage temperature range
V_I < 0 or V_I > V_CC
V_O < 0
E package
M package
MIN MAX UNIT
–0.5
6V
±20 mA
–50 mA
±50 mA
80
°C/W
86
–65 150 °C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The input and output negative voltage ratings may be exceeded if the input and output current ratings are observed.
(3) The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions⁽¹⁾
V_CC
V_IH
V_IL
V_I
V_O
I_OL
∆t/∆v
Supply voltage
High-level input voltage
Low-level input voltage
Input voltage
Output voltage
Low-level output current
Input transition rise or fall rate
T_A = 25°C
MIN MAX
4.5 5.5
2
0.8
0 V_CC
0 5.5
24
10
–40°C TO
85°C
MIN MAX
4.5
5.5
2
0.8
0
V_CC
0
5.5
24
10
–55°C TO
125°C
MIN MAX
4.5 5.5
2
0.8
0 V_CC
0 5.5
24
10
UNIT
V
V
V
V
V
mA
ns/V
(1) All unused inputs of the device must be held at V_CC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
Electrical Characteristics
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
V_OL
I_I
I_CC
∆I_CC
C_i
V_I = V_IH or V_IL
V_I = V_CC or GND
V_I = V_CC or GND,
V_I = V_CC– 2.1 V
I_OL = 50 mA
I_OL = 24 mA
I_OL = 50 mA⁽¹⁾
I_OL = 75 mA⁽¹⁾
I_O = 0
V_CC
4.5 V
4.5 V
5.5 V
5.5 V
5.5 V
5.5 V
4.5 V to 5.5 V
T_A = 25°C
MIN MAX
0.1
0.36
±0.1
4
2.4
10
–40°C TO
85°C
MIN MAX
0.1
0.44
1.65
±1
40
2.8
10
–55°C TO
125°C
MIN MAX
0.1
0.5
1.65
UNIT
V
±1 µA
80 µA
3 mA
10 pF
(1) Test one output at a time, not exceeding 1-second duration. Measurement is made by forcing indicated current and measuring voltage
to minimize power dissipation. Test verifies a minimum 50-Ω transmission-line drive capability at 85°C and 75-Ω transmission-line drive
capability at 125°C.
2
Submit Documentation Feedback