|
BQ24295RGER Datasheet, PDF (19/45 Pages) Texas Instruments – I2C Controlled 3A Single Cell USB Charger With Narrow VDC 4.5-5.5V Adjustable Voltage at 1.5A Synchronous Boost Operation | |||
|
◁ |
www.ti.com
bq24295
SLUSBC1 â SEPTEMBER 2013
Boost Voltage/Thermal Regulation Control Register REG06 (default 10010011, or 0x93)
BIT
DESCRIPTION
NOTE
Bit 7
Bit 6
Bit 5
BOOSTV[3]
BOOSTV[2]
BOOSTV[1]
512mV
256mV
128mV
Offset: 4.55V
Range: 4.55V â 5.51V
Default:5.126V(1001)
Bit 4 BOOSTV[0]
64mV
Bit 3
Bit 2
BHOT[1]
BHOT[0]
Set Boost Mode temperature monitor
threshold voltage to disable boost mode
Voltage to disable boost mode
00 â Vbhot1 (33% of REGN or 55â¦C w/ 103AT
thermistor)
01 â Vbhot0 (36% of REGN or 60â¦C w/ 103AT
thermistor)
10 â Vbhot2 (30% of REGN or 65â¦C w/ 103AT
thermistor)
11 â Disable boost mode thermal protection.
Default: Vbhot1 (00)
Note: For BHOT[1:0]=11, boost mode operates without
temperature monitor and the NTC_FAULT is generated based
on Vbhot1 threshold
Thermal Regulation Threshold
Bit 1
Bit 0
TREG[1]
TREG[0]
00 â 60°C, 01 â 80°C, 10 â 100°C, 11 â
120°C
Default: 120°C (11)
Misc Operation Control Register REG07 (default 01001011, or 4B)
BIT
DESCRIPTION
Force DPDM detection
Bit 7
DPDM_EN
0 â Not in D+/Dâ detection;
1 â Force D+/Dâ detection when VBUS power is
presence
Safety Timer Setting during Input DPM and Thermal Regulation
Bit 6
TMR2X_EN
0 â Safety timer not slowed by 2X during input DPM
or thermal regulation,
1 â Safety timer slowed by 2X during input DPM or
thermal regulation
Force BATFET Off
Bit 5
BATFET_Disable
0 â Allow BATFET (Q4) turn on, 1 â Turn off
BATFET (Q4)
Bit 4
Reserved
0 - Reserved
Bit 3
Reserved
1 - Reserved
Bit 2
Reserved
0 - Reserved
Bit 1
INT_MASK[1]
0 â No INT during CHRG_FAULT, 1 â INT on
CHRG_FAULT
Bit 0
INT_MASK[0]
0 â No INT during BAT_FAULT, 1 â INT on
BAT_FAULT
NOTE
Default: Not in D+/Dâ detection (0), Back to 0
after detection complete
Default: Safety timer slowed by 2X (1)
Default: Allow BATFET (Q4) turn on(0)
Default: INT on CHRG_FAULT (1)
Default: INT on BAT_FAULT (1)
System Status Register REG08
BIT
DESCRIPTION
Bit 7
VBUS_STAT[1] 00 â Unknown (no input, or DPDM detection incomplete), 01 â USB host, 10 â Adapter port, 11 â OTG
Bit 6
VBUS_STAT[0]
Bit 5
Bit 4
CHRG_STAT[1] 00 â Not Charging, 01 â Pre-charge (<VBATLOWV), 10 â Fast Charging, 11 â Charge Termination Done
CHRG_STAT[0]
Bit 3
DPM_STAT
0 â Not DPM, 1 â VINDPM or IINDPM
Bit 2
PG_STAT
0 â Not Power Good, 1 â Power Good
Bit 1
THERM_STAT 0 â Normal, 1 â In Thermal Regulation
Bit 0
VSYS_STAT 0 â Not in VSYSMIN regulation (BAT>VSYSMIN), 1 â In VSYSMIN regulation (BAT<VSYSMIN)
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: bq24295
Submit Documentation Feedback
19
|
▷ |