XIO2213A Datasheet, PDF (1/4 Pages) Texas Instruments – XIO2213A PCI Express to 1394b OHCI with 3-Port PHY

www.ti.com
XIO2213A
SCPS187A – JANUARY 2008 – REVISED MARCH 2008
XIO2213A PCI Express to 1394b OHCI with 3-Port PHY
FEATURES
1
•2 Full x1 PCI Express Throughput
• Fully Compliant with PCI Express Base
Specification, Revision 1.1
• Utilizes 100-MHz Differential PCI Express
Common Reference Clock or 125-MHz
Single-Ended Reference Clock
• Fully supports provisions of IEEE P1394b-2002
• Fully Compliant With Provisions of IEEE Std
1394-1995 for a High-Performance Serial Bus
and IEEE Std 1394a-2000
• Fully Compliant with 1394 Open Host
Controller Interface Specification, Revision 1.1
and Revision 1.2 draft
• Three IEEE Std 1394b Fully Compliant Cable
Ports at 100M Bits/s, 200M Bits/s, 400M Bits/s,
and 800M Bits/s
• Cable Ports Monitor Line Conditions for Active
Connection To Remote Node
• Cable Power Presence Monitoring
• EEPROM Configuration Support to Load the
Global Unique ID for the 1394 Fabric
• Support for D1, D2, D3_hot
• Active State Link Power Management Saves
Power When Packet Activity on the PCI
Express™ Link is Idle, Using Both L0s and L1
States
• Eight 3.3-V, Multifunction, General-Purpose I/O
Terminals
DESCRIPTION
The Texas Instruments XIO2213A is a PCI Express to PCI translation bridge where the PCI bus interface is
internally connected to a 1394b open host controller link-layer controller with a three-port 1394b PHY. The
PCI-Express to PCI translation bridge is fully compatible with the PCI Express to PCI/PCI-X Bridge Specification,
Revision 1.0. Also, the bridge supports the standard PCI-to-PCI bridge programming model. The 1394b OHCI
controller function is fully compatible with IEEE Standard 1394b and the latest 1394 Open Host Controller
Interface (OHCI) Specification.
The XIO2213A simultaneously supports up to four posted write transactions, four non-posted transactions, and
four completion transactions pending in each direction at any time. Each posted write data queue and completion
data queue can store up to 8K bytes of data. The non-posted data queues can store up to 128 bytes of data.
The PCI Express interface supports a x1 link operating at full 250 MB/s packet throughput in each direction
simultaneously. Also, the bridge supports the advanced error reporting capability including ECRC as defined in
the PCI Express Base Specification, Revision 1.1. Supplemental firmware or software is required to fully utilize
both of these features.
Robust pipeline architecture is implemented to minimize system latency. If parity errors are detected, then packet
poisoning is supported for both upstream and downstream operations.
The PCIe Power management (PM) features include active state link PM, PME mechanisms, and all
conventional PCI D-states. If the active state link PM is enabled, then the link automatically saves power when
idle using the L0s and L1 states. PM active state NAK, PM PME, and PME-to-ACK messages are supported.
The bridge is compliant with the latest PCI Bus Power Management Specification and provides several
low-power modes, which enable the host power system to further reduce power consumption
Eight general-purpose inputs and outputs (GPIOs), configured through accesses to the PCI Express
configuration space, allow for further system control and customization.
Deep FIFOs are provided to buffer 1394 data and accommodate large host bus latencies. The device provides
physical write posting and a highly tuned physical data path for SBP-2 performance. The device is capable of
transferring data between the PCI Express bus and the 1394 bus at 100M bits/s, 200M bits/s, 400M bits/s, and
800M bits/s. The device provides three 1394 ports that have separate cable bias (TPBIAS).
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PCI Express is a trademark of PCI-SIG.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008, Texas Instruments Incorporated