TPS60100 Datasheet, PDF (1/22 Pages) Texas Instruments – REGULATED 3.3 V 200-mA LOW-NOISE CHARGE PUMP DC/DC CONVERTER

features
D Up to 200-mA Output Current
D Less Than 5-mV_pp Output Voltage Ripple
D No Inductors Required/Low EMI
D Regulated 3.3-V ±4% Output
D Only Four External Components Required
D Up to 90% Efficiency
D 1.8-V to 3.6-V Input Voltage Range
D 50-µA Quiescent Supply Current
D 0.05-µA Shutdown Current
D Load Isolated in Shutdown
D Space-Saving Thermally-Enhanced TSSOP
PowerPAD™ Package
D Evaluation Module Available
(TPS60100EVM–131)
description
The TPS60100 step-up, regulated charge pump
generates a 3.3-V ±4% output voltage from a
1.8-V to 3.6-V input voltage (two alkaline, NiCd, or
NiMH batteries). Output current is 200 mA from a
2-V input. Only four external capacitors are
needed to build a complete low-noise dc/dc
converter. The push-pull operating mode of two
single-ended charge pumps assures the low
output voltage ripple as current is continuously
transferred to the output. From a 2-V input, the
TPS60100 can start into full load with loads as low
as 16 Ω.
The TPS60100 features either constant frequen-
cy mode to minimize noise and output voltage
ripple or the power-saving pulse-skip mode to
extend battery life at light loads. The TPS60100
switching frequency is 300 kHz. The logic
shutdown function reduces the supply current to
1-µA (max) and disconnects the load from the
input. Special current-control circuitry prevents
excessive current from being drawn from the
battery during start-up. This dc/dc converter
requires no inductors and has low EMI. It is
available in the small 20-pin TSSOP PowerPAD™
package (PWP).
TPS60100
REGULATED 3.3 V 200-mA LOW-NOISE
CHARGE PUMP DC/DC CONVERTER
SLVS213B – MAY 1999 – REVISED SEPTEMBER 1999
applications
Replaces DC/DC Converters With Inductors in
– Battery-Powered Applications
– Two Battery Cells to 3.3-V Conversion
– Portable Instruments
– Battery-Powered Microprocessor and
DSP Systems
– Miniature Equipment
– Backup-Battery Boost Converters
– PDAs
– Laptops
– Handheld Instrumentation
– Medical Instruments
– Cordless Phones
output voltage ripple
3.45
3.4
3.35
3.3
3.25
3.2
SKIP =COM = 3V8 = 0 V
VIN = 2.4 V
3.15
IO = 200 mA
3.1
CO = 22 µF
X5R Ceramic
3.05 _{0 1 2 3 4 5 6 7 8 9 10}
t – Time – µs
typical operating circuit
INPUT
1.8 V to
3.6 V
CIN ⁺
10 µF
C1F
2.2 µF
SKIP COM 3V8
IN
OUT
IN
OUT
TPS60100 FB
C1+
C2+
C1–
C2–
OUTPUT
3.3 V
200 mA
+ _CO
22 µF
C2F
2.2 µF
OFF/ON
ENABLE SYNC
PGND GND
Figure 1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments Incorporated.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright © 1999, Texas Instruments Incorporated
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
1