SN74GTLPH32945_07 Datasheet, PDF (1/17 Pages) Texas Instruments – 32-BIT LVTTL-TO-GTLP BUS TRANSCEIVER

www.ti.com
FEATURES
• Member of the Texas Instruments Widebus+™
Family
• TI-OPC™ Circuitry Limits Ringing on
Unevenly Loaded Backplanes
• OEC™ Circuitry Improves Signal Integrity and
Reduces Electromagnetic Interference
• Bidirectional Interface Between GTLP Signal
Levels and LVTTL Logic Levels
• LVTTL Interfaces Are 5-V Tolerant
• Medium-Drive GTLP Outputs (50 mA)
SN74GTLPH32945
32-BIT LVTTL-TO-GTLP BUS TRANSCEIVER
SCES293C – OCTOBER 1999 – REVISED JUNE 2005
• LVTTL Outputs (–24 mA/24 mA)
• GTLP Rise and Fall Times Designed for
Optimal Data-Transfer Rate and Signal
Integrity in Distributed Loads
• I_off, Power-Up 3-State, and BIAS V_CC Support
Live Insertion
• Bus Hold on A-Port Data Inputs
• Distributed V_CC and GND Pins Minimize
High-Speed Switching Noise
• Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
DESCRIPTION/ORDERING INFORMATION
The SN74GTLPH32945 is a medium-drive, 32-bit bus transceiver that provides LVTTL-to-GTLP and
GTLP-to-LVTTL signal-level translation. It is partitioned as four 8-bit transceivers. The device provides a
high-speed interface between cards operating at LVTTL logic levels and a backplane operating at GTLP signal
levels. High-speed (about three times faster than standard TTL or LVTTL) backplane operation is a direct result
of GTLP's reduced output swing (<1 V), reduced input threshold levels, improved differential input, OEC circuitry,
and TI-OPC circuitry. Improved GTLP OEC and TI-OPC circuits minimize bus-settling time and have been
designed and tested using several backplane models. The medium drive allows incident-wave switching in
heavily loaded backplanes with equivalent load impedance down to 19 Ω.
GTLP is the Texas Instruments derivative of the Gunning Transceiver Logic (GTL) JEDEC standard JESD 8-3.
The ac specification of the SN74GTLPH32945 is given only at the preferred higher noise margin GTLP, but the
user has the flexibility of using this device at either GTL (V_TT = 1.2 V and V_REF = 0.8 V) or GTLP (V_TT = 1.5 V and
V_REF = 1 V) signal levels.
Normally, the B port operates at GTLP signal levels. The A-port and control inputs operate at LVTTL logic levels,
but are 5-V tolerant and are compatible with TTL and 5-V CMOS inputs. V_REF is the B-port differential input
reference voltage.
This device is fully specified for live-insertion applications using I_off, power-up 3-state, and BIAS V_CC. The I_off
circuitry disables the outputs, preventing damaging current backflow through the device when it is powered
down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power
down, which prevents driver conflict. The BIAS V_CC circuitry precharges and preconditions the B-port input/output
connections, preventing disturbance of active data on the backplane during card insertion or removal, and
permits true live-insertion capability.
This GTLP device features TI-OPC circuitry, which actively limits overshoot caused by improperly terminated
backplanes, unevenly distributed cards, or empty slots during low-to-high signal transitions. This improves signal
integrity, which allows adequate noise margin to be maintained at higher frequencies.
Active bus-hold circuitry holds unused or undriven LVTTL data inputs at a valid logic state. Use of pullup or
pulldown resistors with the bus-hold circuitry is not recommended.
ORDERING INFORMATION
T_A
–40°C to 85°C
PACKAGE ⁽¹⁾
LFBGA – GKE
Tape and reel
ORDERABLE PART NUMMER
SN74GTLPH32945KR
TOP-SIDE MARKING
GM45
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus+, TI-OPC, OEC are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2005, Texas Instruments Incorporated