SN54LVTH16952_07 Datasheet, PDF (1/15 Pages) Texas Instruments – 3.3-V ABT 16-BIT REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS

SN54LVTH16952, SN74LVTH16952
3.3-V ABT 16-BIT REGISTERED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS697G – JULY 1997 – REVISED APRIL 2000
D Members of the Texas Instruments
Widebus ™ Family
D State-of-the-Art Advanced BiCMOS
Technology (ABT) Design for 3.3-V
Operation and Low Static-Power
Dissipation
D Support Mixed-Mode Signal Operation (5-V
Input and Output Voltages With 3.3-V V_CC)
D Support Unregulated Battery Operation
Down to 2.7 V
D Typical V_OLP (Output Ground Bounce)
<0.8 V at V_CC = 3.3 V, T_A = 25°C
D I_off and Power-Up 3-State Support Hot
Insertion
D Bus Hold on Data Inputs Eliminates the
Need for External Pullup/Pulldown
Resistors
D Distributed V_CC and GND Pins Minimize
High-Speed Switching Noise
D Flow-Through Architecture Optimizes PCB
Layout
D Latch-Up Performance Exceeds 500 mA Per
JESD 17
D ESD Protection Exceeds 2000 V Per
MIL-STD-883, Method 3015; Exceeds 200 V
Using Machine Model (C = 200 pF, R = 0)
D Package Options Include Plastic Shrink
Small-Outline (DL) and Thin Shrink
Small-Outline (DGG) Packages and 380-mil
Fine-Pitch Ceramic Flat (WD) Package
SN54LVTH16952 . . . WD PACKAGE
SN74LVTH16952 . . . DGG OR DL PACKAGE
(TOP VIEW)
1OEAB 1
1CLKAB 2
1CLKENAB 3
GND 4
1A1 5
1A2 6
V_CC 7
1A3 8
1A4 9
1A5 10
GND 11
1A6 12
1A7 13
1A8 14
2A1 15
2A2 16
2A3 17
GND 18
2A4 19
2A5 20
2A6 21
V_CC 22
2A7 23
2A8 24
GND 25
2CLKENAB 26
2CLKAB 27
2OEAB 28
56 1OEBA
55 1CLKBA
54 1CLKENBA
53 GND
52 1B1
51 1B2
50 V_CC
49 1B3
48 1B4
47 1B5
46 GND
45 1B6
44 1B7
43 1B8
42 2B1
41 2B2
40 2B3
39 GND
38 2B4
37 2B5
36 2B6
35 V_CC
34 2B7
33 2B8
32 GND
31 2CLKENBA
30 2CLKBA
29 2OEBA
description
The ’LVTH16952 devices are 16-bit registered transceivers designed for low-voltage (3.3-V) V_CC operation, but
with the capability to provide a TTL interface to a 5-V system environment.
These devices can be used as two 8-bit transceivers or one 16-bit transceiver. Data on the A or B bus is stored
in the registers on the low-to-high transition of the clock (CLKAB or CLKBA) input, provided that the clock-enable
(CLKENAB or CLKENBA) input is low. Taking the output-enable (OEAB or OEBA) input low accesses the data
on either port.
Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level.
When V_CC is between 0 and 1.5 V, the devices are in the high-impedance state during power up or power down.
However, to ensure the high-impedance state above 1.5 V, OE should be tied to V_CC through a pullup resistor;
the minimum value of the resistor is determined by the current-sinking capability of the driver.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright © 2000, Texas Instruments Incorporated
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
1