SN54LVTH16543_07 Datasheet, PDF (1/14 Pages) Texas Instruments – 3.3-V ABT 16-BIT REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS

SN54LVTH16543, SN74LVTH16543
3.3-V ABT 16-BIT REGISTERED TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS699D – JULY 1997 – REVISED APRIL 1999
D Members of the Texas Instruments
Widebus ™ Family
D State-of-the-Art Advanced BiCMOS
Technology (ABT) Design for 3.3-V
Operation and Low Static-Power
Dissipation
D Support Mixed-Mode Signal Operation (5-V
Input and Output Voltages With 3.3-V V_CC)
D Support Unregulated Battery Operation
Down to 2.7 V
D I_off and Power-Up 3-State Support Hot
Insertion
D Bus Hold on Data Inputs Eliminates the
Need for External Pullup/Pulldown
Resistors
D Typical V_OLP (Output Ground Bounce)
< 0.8 V at V_CC = 3.3 V, T_A = 25°C
D Distributed V_CC and GND Pin Configuration
Minimizes High-Speed Switching Noise
D Flow-Through Architecture Optimizes PCB
Layout
D Latch-Up Performance Exceeds 500 mA Per
JESD 17
D ESD Protection Exceeds 2000 V Per
MIL-STD-883, Method 3015; Exceeds 200 V
Using Machine Model (C = 200 pF, R = 0)
D Package Options Include Plastic Shrink
Small-Outline (DL) and Thin Shrink
Small-Outline (DGG) Packages and 380-mil
Fine-Pitch Ceramic Flat (WD) Package
Using 25-mil Center-to-Center Spacings
SN54LVTH16543 . . . WD PACKAGE
SN74LVTH16543 . . . DGG OR DL PACKAGE
(TOP VIEW)
1OEAB 1
1LEAB 2
1CEAB 3
GND 4
1A1 5
1A2 6
V_CC 7
1A3 8
1A4 9
1A5 10
GND 11
1A6 12
1A7 13
1A8 14
2A1 15
2A2 16
2A3 17
GND 18
2A4 19
2A5 20
2A6 21
V_CC 22
2A7 23
2A8 24
GND 25
2CEAB 26
2LEAB 27
2OEAB 28
56 1OEBA
55 1LEBA
54 1CEBA
53 GND
52 1B1
51 1B2
50 V_CC
49 1B3
48 1B4
47 1B5
46 GND
45 1B6
44 1B7
43 1B8
42 2B1
41 2B2
40 2B3
39 GND
38 2B4
37 2B5
36 2B6
35 V_CC
34 2B7
33 2B8
32 GND
31 2CEBA
30 2LEBA
29 2OEBA
description
The ’LVTH16543 devices are 16-bit registered transceivers designed for low-voltage (3.3-V) V_CC operation, but
with the capability to provide a TTL interface to a 5-V system environment. These devices can be used as two
8-bit transceivers or one 16-bit transceiver. Separate latch-enable (LEAB or LEBA) and output-enable (OEAB
or OEBA) inputs are provided for each register to permit independent control in either direction of data flow.
The A-to-B enable (CEAB) input must be low to enter data from A or to output data from B. If CEAB is low and
LEAB is low, the A-to-B latches are transparent; a subsequent low-to-high transition of LEAB puts the A latches
in the storage mode. With CEAB and OEAB both low, the 3-state B outputs are active and reflect the data present
at the output of the A latches. Data flow from B to A is similar but requires using the CEBA, LEBA, and OEBA
inputs.
Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus is a trademark of Texas Instruments Incorporated.
UNLESS OTHERWISE NOTED this document contains PRODUCTION
DATA information current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all
parameters.
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
Copyright © 1999, Texas Instruments Incorporated
1