SN54ABTH16245 Datasheet, PDF (1/12 Pages) Texas Instruments – 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS

D Members of the Texas Instruments
Widebus ™ Family
D State-of-the-Art EPIC-ΙΙB™ BiCMOS Design
Significantly Reduces Power Dissipation
D Typical V_OLP (Output Ground Bounce) < 1 V
at V_CC = 5 V, T_A = 25°C
D High-Impedance State During Power Up
and Power Down
D Distributed V_CC and GND Pin Configuration
Minimizes High-Speed Switching Noise
D Flow-Through Architecture Optimizes PCB
Layout
D High-Drive Outputs (–32-mA I_OH, 64-mA I_OL)
D Bus Hold on Data Inputs Eliminates the
Need for External Pullup/Pulldown
Resistors
D Latch-Up Performance Exceeds 500 mA Per
JESD 17
D Package Options Include Plastic Shrink
Small-Outline (DL), Thin Shrink
Small-Outline (DGG), and Thin Very
Small-Outline (DGV) Packages and 380-mil
Fine-Pitch Ceramic Flat (WD) Package
Using 25-mil Center-to-Center Spacings
description
SN54ABTH16245, SN74ABTH16245
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS662I – MARCH 1996 – REVISED MARCH 1999
SN54ABTH16245 . . . WD PACKAGE
SN74ABTH16245 . . . DGG, DGV, OR DL PACKAGE
(TOP VIEW)
1DIR 1
1B1 2
1B2 3
GND 4
1B3 5
1B4 6
V_CC 7
1B5 8
1B6 9
GND 10
1B7 11
1B8 12
2B1 13
2B2 14
GND 15
2B3 16
2B4 17
V_CC 18
2B5 19
2B6 20
GND 21
2B7 22
2B8 23
2DIR 24
48 1OE
47 1A1
46 1A2
45 GND
44 1A3
43 1A4
42 V_CC
41 1A5
40 1A6
39 GND
38 1A7
37 1A8
36 2A1
35 2A2
34 GND
33 2A3
32 2A4
31 V_CC
30 2A5
29 2A6
28 GND
27 2A7
26 2A8
25 2OE
The ’ABTH16245 devices are 16-bit noninverting
3-state transceivers that provide synchronous
two-way communication between data buses.
The control-function implementation minimizes
external timing requirements.
These devices can be used as two 8-bit transceivers or one 16-bit transceiver. They allow data transmission
from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control
(DIR) input. The output-enable (OE) input can be used to disable the devices so that the buses are effectively
isolated.
When V_CC is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down.
However, to ensure the high-impedance state above 2.1 V, OE should be tied to V_CC through a pullup resistor;
the minimum value of the resistor is determined by the current-sinking capability of the driver.
Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level.
The SN54ABTH16245 is characterized for operation over the full military temperature range of –55°C to 125°C.
The SN74ABTH16245 is characterized for operation from –40°C to 85°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus and EPIC-ΙΙB are trademarks of Texas Instruments Incorporated.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright © 1999, Texas Instruments Incorporated
On products compliant to MIL-PRF-38535, all parameters are tested
unless otherwise noted. On all other products, production
processing does not necessarily include testing of all parameters.
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
1