SN54ABT16652_07 Datasheet, PDF (1/16 Pages) Texas Instruments – 16-BIT BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS

SN54ABT16652, SN74ABT16652
16-BIT BUS TRANSCEIVERS AND REGISTERS
WITH 3-STATE OUTPUTS
SCBS215B – FEBRUARY 1991 – REVISED JANUARY 1997
D Members of the Texas Instruments
Widebus™ Family
D State-of-the-Art EPIC-ΙΙB™ BiCMOS Design
Significantly Reduces Power Dissipation
D Latch-Up Performance Exceeds 500 mA Per
JEDEC Standard JESD-17
D Typical V_OLP (Output Ground Bounce)
< 1 V at V_CC = 5 V, T_A = 25°C
D Distributed V_CC and GND Pin Configuration
Minimizes High-Speed Switching Noise
D Flow-Through Architecture Optimizes PCB
Layout
D High-Drive Outputs (–32-mA I_OH, 64-mA I_OL)
D Package Options Include Plastic 300-mil
Shrink Small-Outline (DL) Package and
380-mil Fine-Pitch Ceramic Flat (WD)
Package Using 25-mil Center-to-Center
Spacings
description
The ’ABT16652 are 16-bit bus transceivers that
consist of D-type flip-flops and control circuitry
arranged for multiplexed transmission of data
directly from the data bus or from the internal
storage registers. These devices can be used as
two 8-bit transceivers or one 16-bit transceiver.
Output-enable (OEAB and OEBA) inputs are
provided to control the transceiver functions.
Select-control (SAB and SBA) inputs are provided
to select whether real-time or stored data is
transferred. The circuitry used for select control
eliminates the typical decoding glitch that occurs
in a multiplexer during the transition between
stored and real-time data. A low input selects
real-time data, and a high input selects stored
data. Figure 1 illustrates the four fundamental
bus-management functions that can be
performed with the ’ABT16652.
SN54ABT16652 . . . WD PACKAGE
SN74ABT16652 . . . DL PACKAGE
(TOP VIEW)
1OEAB 1
1CLKAB 2
1SAB 3
GND 4
1A1 5
1A2 6
V_CC 7
1A3 8
1A4 9
1A5 10
GND 11
1A6 12
1A7 13
1A8 14
2A1 15
2A2 16
2A3 17
GND 18
2A4 19
2A5 20
2A6 21
V_CC 22
2A7 23
2A8 24
GND 25
2SAB 26
2CLKAB 27
2OEAB 28
56 1OEBA
55 1CLKBA
54 1SBA
53 GND
52 1B1
51 1B2
50 V_CC
49 1B3
48 1B4
47 1B5
46 GND
45 1B6
44 1B7
43 1B8
42 2B1
41 2B2
40 2B3
39 GND
38 2B4
37 2B5
36 2B6
35 V_CC
34 2B7
33 2B8
32 GND
31 2SBA
30 2CLKBA
29 2OEBA
Data on the A- or B-data bus, or both, can be stored in the internal D-type flip-flops by low-to-high transitions
at the appropriate clock (CLKAB or CLKBA) inputs regardless of the select- or enable-control inputs. When SAB
and SBA are in the real-time transfer mode, it is possible to store data without using the internal D-type flip-flops
by simultaneously enabling OEAB and OEBA. In this configuration, each output reinforces its input. When all
other data sources to the two sets of bus lines are at high impedance, each set of bus lines remains at its last
state.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus and EPIC-ΙΙB are trademarks of Texas Instruments Incorporated.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright © 1997, Texas Instruments Incorporated
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
1