|
PTH03030W Datasheet, PDF (1/18 Pages) Texas Instruments – 30-A, 3.3-V Input Non-Isolated Wide-Output Adjust Power Module | |||
|
PTH03030W â3.3-V Input
30-A, 3.3-V Input Non-Isolated
Wide-Output Adjust Power Module
SLTS209B â MAY 2003 â REVISED JANUARY 2004
NOMINAL SIZE = 1.37 in x 1.12 in
(34,8 mm x 28,5 mm)
Features
⢠Up to 30-A Output Current
⢠3.3-V Input Voltage
⢠Wide-Output Voltage Adjust
(0.8 V to 2.5 V)
⢠135 W/in³ Power Density
⢠Efficiencies up to 93 %
⢠On/Off Inhibit
⢠Pre-Bias Startup
⢠Margin Up/Down Controls
⢠Under-Voltage Lockout
⢠Auto-Track⢠Sequencing
⢠Output Over-Current Protection
(Non-Latching, Auto-Reset)
⢠Operating Temp: â40 to +85 °C
⢠Over-Temperature Shutdown
⢠Safety Agency Approvals:
UL 1950, CSA 22.2 950, EN60950
VDE (Pending)
⢠Point-of-Load Alliance (POLA)
Compatible
Description
The PTH03030 is a series of high-
current non-isolated power modules
from Texas Instruments. The product is
characterized by high efficiencies, and
up to 30 A of output current, while oc-
cupying a mere 1.64 in² of PCB area. In
terms of cost, size, and performance, the
series provides OEMâs with a flexible
module that meets the requirements of
the most complex and demanding mixed-
signal applications. These include the
most densly populated, multi-processor
systems that incorporate high-speed
DSPâs, microprocessors, and ASICs.
The series uses double-sided surface
mount construction and provides high-
performance step-down power conversion
from a 3.3-V input bus voltage. The out-
Standard Application
put voltage of the PTH03030W can be
set to any value over the range 0.8 V to
2.5 V, using a single resistor.
This series includes Auto-Trackâ¢.
Auto-Track simplifies power-up and
power-down supply voltage sequencing
in a system by enabling modules to track
each other, or any other external voltage.
Each model also includes an on/off
inhibit, output voltage adjust (trim), and
margin up/down controls. An output
voltage sense ensures tight load regulation,
and an output over-current and thermal
shutdown feature provide for protection
against external load faults.
Package options inlude both through-
hole and surface mount configurations.
Pin Configuration
Pin Function
1 GND
2 Vin
3 GND
4 Inhibit *
5 Vo Adjust
6 Vo Sense
7 GND
8 Vout
9 Vout
10 GND
11 Track
12 Margin Down *
13 Margin Up *
* Denotes negative logic:
Open = Normal operation
Ground = Function active
ASuteoq-uTreancckiâ¢ng
Track
Margin Down
Margin Up
VIN
Inhibit
CIN
1,500 µF
(Required)
GND
13 12 11
1
10
2
PTH03030W
9
(Top View)
8
3
7
456
RSET
0.5 %, 0.1 W
(Required)
COUT
330 µF
(Optional)
Rset = Required to set the desired output voltage
higher than 0.8 V (see spec. table for values).
Cin = Required 1,500 µF capacitor.
Cout = Optional 330 µF capacitor.
VOUT
Vo Sense
L
O
A
D
GND
For technical support and further information, visit http://power.ti.com
|
▷ |