MSP430FG461X Datasheet, PDF (1/105 Pages) Texas Instruments – MIXED SIGNAL MICROCONTROLLER

MSP430FG461x
MIXED SIGNAL MICROCONTROLLER
D Low Supply-Voltage Range, 1.8 V to 3.6 V
D Ultralow-Power Consumption:
− Active Mode: 350 µA at 1 MHz, 2.2 V
− Standby Mode: 1.1 µA
− Off Mode (RAM Retention): 0.3 µA
D Five Power Saving Modes
D Wake-Up From Standby Mode in less
than 6 µs
D 16-Bit RISC Architecture, Extended
Memory, 125-ns Instruction Cycle Time
D Three Channel Internal DMA
D 12-Bit A/D Converter With Internal
Reference, Sample-and-Hold and Autoscan
Feature
D Three Configurable Operational Amplifiers
D Dual 12-Bit D/A Converters With
Synchronization
D 16-Bit Timer_A With Three
Capture/Compare Registers
D 16-Bit Timer_B With Seven
Capture/Compare-With-Shadow Registers
D On-Chip Comparator
D Supply Voltage Supervisor/Monitor With
Programmable Level Detection
D Serial Communication Interface (USART1),
Select Asynchronous UART or
Synchronous SPI by Software
SLAS508 − APRIL 2006
D Universal Serial Communication Interface
− Enhanced UART supporting
auto-baudrate detection
− IrDA Encoder and Decoder
− Synchronous SPI
− I2C^TM
D Serial Onboard Programming,
No External Programming Voltage Needed
Programmable Code Protection by Security
Fuse
D Brownout Detector
D Basic Timer with Real Time Clock Feature
D Integrated LCD Driver up to 160 Segments
With Regulated Charge Pump
D Family Members Include:
− MSP430FG4616:
92KB+256B Flash Memory,
4KB RAM
− MSP430FG4617:
92KB+256B Flash Memory,
8KB RAM
− MSP430FG4618:
116KB+256B Flash Memory,
8KB RAM
− MSP430FG4619:
120KB+256B Flash Memory,
4KB RAM
D For Complete Module Descriptions, Refer
to the MSP430x4xx Family User’s Guide
description
The Texas Instruments MSP430 family of ultralow power microcontrollers consist of several devices featuring
different sets of peripherals targeted for various applications. The architecture, combined with five low power
modes is optimized to achieve extended battery life in portable measurement applications. The device features
a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that attribute to maximum code efficiency.
The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 6µs.
The MSP430FG461x series are microcontroller configurations with two 16-bit timers, a high performance 12-bit
A/D converter, dual 12-bit D/A converters, three configurable operational amplifiers, one universal serial
communication interface (USCI), one universal synchronous/asynchronous communication interface
(USART), DMA, 80 I/O pins, and a liquid crystal display (LCD) driver with regulated charge pump.
Typical applications for this device include analog and digital sensor systems, digital motor control, remote
controls, thermostats, digital timers, hand-held meters, etc.
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range
from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage
because very small parametric changes could cause the device not to meet its published specifications. These devices have limited
built-in ESD protection.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
Copyright  2006, Texas Instruments Incorporated
1