ISO7631FM Datasheet, PDF (1/31 Pages) Texas Instruments – Low Power Triple and Quad Channels Digital Isolators

www.ti.com
ISO7631FM, ISO7631FC
ISO7640FC, ISO7641FC
SLLSEC3A – SEPTEMBER 2012 – REVISED SEPTEMBER 2012
Low Power Triple and Quad Channels Digital Isolators
Check for Samples: ISO7631FM, ISO7631FC, ISO7640FC, ISO7641FC
FEATURES
1
• Signaling Rate: 150 Mbps (M-Grade), 25 Mbps
(C-Grade)
• Robust Design with Integrated Noise Filter
(C-Grade)
• Low Power Consumption, Typical I_CC per
Channel (3.3V Supplies):
– ISO7631FM: 2 mA at 10 Mbps
– ISO7631FC: 1.5 mA at 10 Mbps
– ISO7640FC: 1.1 mA at 10 Mbps
– ISO7641FC: 1.3 mA at 10 Mbps
• Extremely low I_{CC_disable}(C-Grade)
• Low Propagation Delay: 7 ns Typical (M-
Grade)
• Output Defaults to Low-state in Fail-safe Mode
• Wide Temperature Range: –40°C to 125°C
• 50 KV/µs Transient Immunity, Typical
• Long Life with SiO₂ Isolation barrier
• Operates From 2.7V (M-Grade), 3.3 V and 5 V
Supply and Logic Levels
• Wide Body SOIC-16 Package
APPLICATIONS
• Optocoupler Replacement in:
– Industrial Fieldbus
– Profibus
– Modbus
– DeviceNet^TM Data Buses
– Servo Control Interface
– Motor Control
– Power Supplies
– Battery Packs
SAFETY AND REGULATORY
APPROVALS
• 2500 V_RMS for 1 Minute per UL 1577 (approved)
• 4000 V_PK VDE Rating for DIN EN 60747-5-2
(VDE 0884 Rev. 2), 1414 V_PK Working Voltage
(approved)
• CSA Component Acceptance Notice
5A(approved)
DESCRIPTION
ISO7631F, ISO7640F and ISO7641F provide galvanic isolation up to 4 KV_PK per VDE. ISO7631F has 3 channels
with two forward and one reverse direction channels. ISO7640F and ISO7641F are quad channel isolators;
ISO7640F has four forward and ISO7641F has three forward and one reverse direction channels. Suffix F
indicates that output defaults to Low-state in fail-safe conditions (see Table 1). M-Grade devices are high speed
isolators capable of 150 Mbps data rate with fast propagation delays whereas C-Grade devices can run up to 25
Mbps data rate with low power consumption and integrated filters for noise-prone applications. C-Grade devices
are recommended for lower speed applications where input noise pulses of less than 6 ns duration need to be
suppressed or lower power consumption is critical.
V_CC1
GND1
INA
INB
INC
IND
NC
GND1
ISO7640
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
V_CC2
GND2
OUTA
OUTB
OUTC
OUTD
EN
GND2
V_CC1
GND1
INA
INB
INC
OUTD
EN1
GND1
ISO7641
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
V_CC2
GND2
OUTA
OUTB
OUTC
IND
EN2
GND2
V_CC1
GND1
INA
INB
OUTC
NC
EN1
GND1
ISO7631
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
V_CC2
GND2
OUTA
OUTB
INC
NC
EN2
GND2
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated