J412DY-12L Datasheet, PDF (2/6 Pages) Teledyne Technologies Incorporated – ESTABLISHED RELIABILITY TO-5 RELAYS

SERIES 412
GENERAL ELECTRICAL SPECIFICATIONS (–65°C to +125°C unless otherwise noted) (Notes 2 & 3)
Contact Arrangement
Rated Duty
Contact Resistance
2 Form C (DPDT)
Continuous
0.1 ohm max. before life; 0.2 ohm max. after life at 1A/28Vdc (measured 1/8" from header)
Contact Load Ratings (DC)
(See Fig. 2 for other DC
resistive voltage/current ratings)
Resistive:
Inductive:
Lamp:
Low Level:
1 Amp/28Vdc
200 mA/28Vdc (320 mH)
100 mA/28Vdc
10 to 50 μA/10 to 50mV
Contact Load Ratings (AC)
Resistive:
250 mA/115Vac, 60 and 400 Hz (Case not grounded)
100 mA/115Vac, 60 and 400 Hz (Case grounded)
Contact Life Ratings
10,000,000 cycles (typical) at low level
1,000,000 cycles (typical) at 0.5A/28Vdc resistive
100,000 cycles min. at all other loads specified above
Contact Overload Rating
2A/28Vdc Resistive (100 cycles min.)
Contact Carry Rating
Contact factory
Coil Operating Power
450 milliwatts typical at nominal rated voltage @ 25°C
Operate Time
2.0 msec max. at nominal rated coil voltage
Release Time
412 Series: 1.5 msec max. 412D, 412DD Series: 4.0 msec max. 412T Series: 7.5 msec max.
Contact Bounce
1.5 msec max.
Intercontact Capacitance
0.4 pf typical
Insulation Resistance
10,000 megohms min. between mutually isolated terminals
Dielectric Strength
Atmospheric pressure: 500 Vrms/60Hz
70,000 ft.: 125 Vrms/60Hz
Negative Coil Transient (Vdc)
412D, 412DD, 412T
1.0 max
Diode P.I.V. (Vdc)
412D, 412DD, 412T
100 min.
412T
Transistor
Characteristics
Base Turn Off Voltage (Vdc)
Emitter-base breakdown Voltage (BVEBO) (@25°C) (Vdc)
Collector-base breakdown Voltage (BVEBO) (@25°C & lc = 100 μA) (Vdc)
0.3 min.
6.0 min.
75 min.
DETAILED ELECTRICAL SPECIFICATIONS (–65°C to +125°C unless otherwise noted) (Note 3)
BASE PART
NUMBERS
(See Note 10 for full P/N example)
Coil Voltage (Vdc)
Nom.
Max.
Coil Resistance
(Ohms ±10% @25°C)
412, 412D, 412T (Note 4)
412DD (Note 4)
Coil Current (mAdc @25°C)
(412DD Series)
Min.
Max.
Coil Current (mAdc @25°C)
(412T Series)
(Note 7)
Min.
Max.
Pick-up Voltage (Vdc, Max.)
412, 412D
412DD
412T (Note 7)
Base Current to Turn On (mAdc, Max.) (412T Series) (Note 7)
Drop-out Voltage (Vdc)
412, 412D, 412T
412DD
Min.
Max.
Min.
Max.
412-5
412D-5
412DD-5
412T-5
5.0
5.8
50
39
93.2
128.2
82.2
112.1
3.5
3.9
3.5
3.00
0.14
2.3
0.6
2.8
412-6
412D-6
412DD-6
412T-6
6.0
8.0
98
78
58.3
78.3
52.9
69.9
4.5
5.2
4.5
2.04
0.18
3.2
0.7
3.4
412-9
412D-9
412DD-9
412T-9
9.0
12.0
220
220
33.0
42.9
35.3
47.4
6.8
7.8
6.8
1.36
0.35
4.9
0.8
5.3
412-12
412D-12
412DD-12
412T-12
12.0
16.0
390
390
25.6
32.8
26.6
35.8
9.0
10.0
9.0
1.03
0.41
6.5
0.9
6.5
412-18
412D-18
412DD-18
412T-18
18.0
24.0
880
880
17.5
22.1
17.9
24.0
13.5
14.5
13.5
0.68
0.59
10.0
1.1
10.0
412-26
412D-26
412DD-26
412T-26
26.5
32.0
1560
1560
14.8
18.5
14.7
19.8
18.0
19.0
18.0
0.50
0.89
13.0
1.4
13.0
PERFORMANCE CURVES
(NOTE 2)
0
.1
.2
TYPICAL RF PERFORMANCE
INSERTION _LOSS
.3
.4
10
1.92
20
30
40
50
60
ISOLATIORNISEAOTCLURAROTNISOSLNOCASOCSNR(TOVASSCWSTRSPO) ^LES
1.22
1.07
1.02
1.01
1.00
70
.01
FIGURE 1
0.5 .1
FREQUENCY (GHz)
1.00
.5 1.0
TYPICAL DC CONTACT RATING (RESISTIVE)
300
250
200
150
100
50
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
FIGURE 2
LOAD CURRENT (AMPS DC)
412 Page 2
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
www.teledynerelays.com
©2003 TELEDYNE RELAYS
412/1203/Q1