AVP2034 Datasheet, PDF (1/5 Pages) Teledyne Technologies Incorporated – HIGH POWER GaNPak B AMPLIFIER

Rev. 1/12
AVP2034
600 TO 2200 MHz, 20 WATTS
HIGH POWER GaNPak B AMPLIFIER
Typical Values
Broadband. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Saturated Power, Psat. . . . . . . . . . . . . . . . . . . . . . . . .
High Third Order I.P. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Small Hermetic Package, Cougar GaNPakB
AVP2034
500-2400 MHz
+40 dB
25 Watts
+50 dBm
AVP2034
CougarGaNPak B
SPECIFICATIONS^*
Parameter
Typical
Frequency (Min.)
500-2400 MHz
Small Signal Gain (Min.)
Gain Flatness (Max.)
Noise Figure (Max.)
40.0 dB
±0.8 dB
3.7 dB
SWR (Max.)
Input/Output
Power Output (Min.)
@ 4dB comp.
Reverse Isolation
DC Current (Max.)
1st Stg: +12V
Linear Oper. 2nd Stg: +28V
Psat w/+8 dBm Input
2nd Stage: +28V
Switching Speed (Max.)
50% TTL to 90% Rise time
or 10% Fall Time^
<1.8:1
+44.0 dBm
+25.1 W
70.0 dB
200 mA
1200 mA
3200 mA
2 ms
Guaranteed
0 to 50 °C -55 to +85 °C
600-2200 MHz 600-2200 MHz
39.0 dB
±1.0 dB
4.6 dB
38.0 dB
±1.2 dB
5.0 dB
2.0:1
2.0:1
+43.5 dBm
+22.4 W
65.0 dB
+43.0 dBm
+20.0 W
65.0 dB
215 mA
1500 mA
3500 mA
4 ms
230 mA
1600 mA
3700 mA
5 ms
HEAT SINK WARNING:
This amplifier requires an adequate heat sink to prevent
damage. Maximum case temperature must not be
exceeded. The package is designed to provide ade-
quate heat transfer to proper aluminum heat sink.
* Measured in a 50-ohm system at +12/+28V.
^ Faster switching speed option available upon request.
INTERMODULATION PERFORMANCE
Typical @ 25 °C
Second Order Harmonic Intercept Point . . . . . . . . . . . . . .
Second Order Two Tone Intercept Point . . . . . . . . . . . . . . .
Third Order Two Tone Intercept Point . . . . . . . . . . . . . . . . .
AVP2034
+70 dBm
+75 dBm
+46 dBm
ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -62 to +125 °C
Maximum Case Temperature, +28V/+32V . . . . . . . . . . . . . . +90 °C/+75 °C
Maximum DC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
+33 Volts
Maximum Continuous RF Input Power . . . . . . . . . . . . . . . .
+12 dBm¹
Maximum Short Term Input Power (1 Minute Max.) . . . . . .
+14 dBm
Maximum Peak Power (3 µsec Max.) . . . . . . . . . . . . . . . . . .
+16 dBm
Burn-in Temperature, +28V . . . . . . . . . . . . . . . . . . . . . . . . .
+85 °C
Thermal Resistance² (θjc) . . . . . . . . . . . . . . . . . . . . . . . . . . +2.2 °C/Watt
Junction Temperature Rise Above Case (Tjc), +28V . . . . .
+60 °C
1 _{If no load or a short on output; decrease input power by +10 dBm.}
2 _{Thermal resistance is based on total power dissipation.}
The AVP2034 amplifier provides nominal output
power of 20-22 Watts. Each amplifier uses control
circuitry to ensure safe startup and automatic
thermal shutdown and recovery. The amplifiers have
an external pin for TTL on/off control. On/Off Low or
High can be specified; standard is Off/Low. The
AVP2034 uses the preamp and driver stages to
provide ~ 40 dB of overall gain.
Heat sinking is required to keep the case
temperatures within a safe operating range. A thin
layer of thermal grease or HiTherm (for example the
HT-2500 series) helps provide a low resistance
thermal path between the case and the mounting
surface. The mounting surface should be metal with
heat conduction of aluminum or better. Heat sink
size depends on whether fan-driven air cooling is
used, or if only convection is used.
Maximum Tj of both amplifiers is 200°C.
DIMENSIONS ARE IN INCHES [MILLIMETERS]
650-691-9800 • Fax: [phone] • Updates: www.teledynemicrowave.com • [e-mail]