T9A-2X Datasheet, PDF (1/3 Pages) TE Connectivity Ltd – Plastic sealed case available

General Purpose Relays
Power Relays
Potter & Brumfield
T9A_2X series, DC coil NC PCB or Panel Mount Relay
n 30A switching in 1 Form B (NC)
n Plastic sealed case available
n Meets UL 508 and 873 spacing - 3.18mm through air, 6.36mm over
surface
n Option for load connections via 0.250” (6.35mm) Q.C. terminals
n UL class F insulation system standard
Typical applications
Energy Management, Lighting, Industrial Controls
Z
Approvals
UL E58304
Technical data of approved types on request
Contact Data
Contact arrangement
1 form B (NC)
Rated voltage
240VAC
Max. switching voltage
240VAC
Rated current
30A
Limiting continuous current
30A
Contact material
AgSnOInO
Min. recommended contact load
1A, 5VDC or 12VAC
Initial contact resistance
75 mΩ at 1A at 5VDC or 12VAC
Frequency of operation, with/without load
360/3600hr
Operate/release time max., including bounce 18/15ms
Electrical endurance
20,000 typical
Contact ratings ¹⁾
Type
Load
Cycles
UL 508/873
AgSnOInO (contact code 6)
NC
30A, 240VAC, Resistive
20x10³
1) Contact ratings at 25°C (unless otherwise noted) with relay properly vented. Remove
vent nib after soldering and cleaning.
Mechanical endurance
10x10⁶ ops.
Coil Data
Coil voltage range
5 to 110VDC
Max. coil power
110% of nominal
Max. coil temperature
155°C
Coil insulation system according UL
Class F
Coil versions, DC coil
Coil
Rated
Operate Release
Coil
Rated coil
code
voltage
voltage
voltage resistance power
VDC
VDC
VDC
Ω±10%
mW
Code D (1W) coil
5
5
3.75
0.5
25
1W
9
9
6.75
0.9
81
1W
12
12
9
1.2
144
1W
15
15
11.25
1.5
225
1W
18
18
13.5
1.8
324
1W
24
24
18
2.4
576
1W
48
48
36
4.8
2304
1W
110
110
82.5
11
12100
1W
All figures are given for coil without preenergization, at ambient temperature +23°C.
Insulation Data
Initial dielectric strength
between open contacts
1500V_rms
01-2014, Rev. 0114
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
between contact and coil
Initial surge withstand voltage
2500V_rms
between contact and coil
6kV
Initial insulation resistance
between insulated elements
1x10⁹Ω
Clearance/creepage
between contact and coil 3.18mm clearance/6.36mm
Other Data
Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content

refer to the Product Compliance Support Center at

www.te.com/customersupport/rohssupportcenter
Ambient temperature
DC coil
-55ºC to 70ºC²⁾
Category of environmental protection
IEC 61810
RT0 - open, RTI - dust protected
RTII - flux proof, RTIII - wash tight
Vibration resistance (functional)
1.65mm max excursions, 10-55 Hz
Shock resistance (functional)
10g for 11msec
Shock resistance (destructive)
100g
Terminal type pcb-tht, pcb-tht + quick connect, and

quick connect
Weight
26g mounting code 1

33g mounting codes 2 and 5
Resistance to soldering heat THT
IEC 60068-2-20
250°C
Packaging/unit
tray/50 pcs., bundle/250 pcs., box/500 pcs.
2) Operating ambient temperature must consider “Must Operate Voltage Change Over
Temperature,” Contact Temperature Rise, Coil Temperature Rise (If coil is not allowed to
cool) and Maximum Coil Temperature. Specification ambient considers 30A load with
coil cooled to ambient.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
1
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.