PD10 Datasheet, PDF (1/1 Pages) TE Connectivity Ltd – PD10 Make & Break Load Switching

KILOVAC 28 - 1800 Vdc High Voltage Relays
PD10 Make & Break Load Switching
Product Facts
n Excellent for control
applications
n PCB and panel mountings
n Rugged design for the most
demanding applications,
including seismic shock
n Small size and weight
n Low power consumption
n No heat sinks required
n Vacuum-sealed; can operate
in explosive and harsh
environments
n 2000 V isolation across
open contacts
n Vacuum dielectric for power
switching
For factory-direct application assistance,
dial 800-253-4560, ext. 2055, or
805-220-2055.
Contact Ratings*
Panel mount version shown above is
applicable to both PD5 and PD10.
For PD10, the two power terminals
are .064" (1.63) diameter. Refer to
PD5 for PCB mount dimensions.
Product Specifications
Contact Arrangement —
PD10A — SPST-NO
PD10B — SPST-NC
PD10P*** — SPST-Latching
Contact Form —
PD10A — A**
PD10B — B**
PD10P*** — P**
Rated Resistive Load @ 320 Vdc —
10 A
Continuous Current Carry, Max.
@ 85°C —
PD10A and PD10B — 25 A
PD10P*** — 30 A
Overload @ 320 Vdc,
(Make/Break) — 20 A
Life, (Mechanical/Rated Load) —
PD10A and PD10B —
500k cycles/10k cycles
PD10P*** — 7,000 cycles
Contact Resistance, Max.,
End of Life —
PD10A and PD10B — 0.030 ohm
PD10P*** — 0.030 ohm
Dielectric at Sea Level —
Power Terminals to Coil and
All Other Points —
PD10A and PD10B — 1,800 Vrms
PD10P*** — 2,000 Vrms
Shock, 11ms, 1/2 Sine (Peak) —
25 g
Vibration, Sinusoidal
(55-2000 Hz, Peak) — 5 g
Operating Ambient Temperature
Range —
PD10A and PD10B — -40°C to +85°C
PD10P*** — -35°C to +65°C
Operate Time, Max., Including
Bounce @ 25°C —
PD10A and PD10B — 10 ms
PD10P*** — 6 ms
Release Time, Max., Including
Bounce @ 25°C —
PD10A and PD10B — 10 ms
PD10P*** — 6 ms
Insulation Resistance @ 500 Vdc,
Min. —
Initial/End of Life — 100 mohm/50 mohm
Weight, Nominal —
71 g (.156 lb)
Notes:
**Contact TE for availability of other
contact forms
***Not available in package shown,
package is the same as the K41P.
Ordering Information
Sample Part Number ᮣ
PD10 A A 5 7
Series:
*Based on extrapolated data. Since each application is unique, user is encour-
aged to verify rating in actual application. The load terminals should always be
connected as follows: Common Contact (A2) positive; Other Contact negative.
Coil Data
Nominal Volts DC
Max. Coil Voltage
Pickup, Max. @ 85°C
Hold, Min. @ 85°C
Dropout, Min. @ -40°C
Coil Resistance (±10%)
12 Vdc
14 Vdc
8 Vdc
3.3 Vdc
.5 Vdc
70 Ω
Ratings listed are for 25°C, sea level conditions
7–56
24 Vdc
28 Vdc
16 Vdc
10 Vdc
1 Vdc
290 Ω
125 Vdc
130 Vdc
80 Vdc
33 Vdc
5 Vdc
4700 Ω
Contact Form:
A = SPST-NO
B = SPST-NC
P = SPST-Latching
Coil Voltage:
2 = 12 Vdc, PCB Version 3 = 24 Vdc, PCB Version
5 = 125 Vdc, PCB Version
A = 12 Vdc, Panel Mount Version
B = 24 Vdc, Panel Mount Version
C = 125 Vdc, Panel Mount Version
Power Terminals:
3 = PCB Solder Connection
5 = Stud Terminal, Panel Mount
Mounting:
5 = PCB Mount
7 = Panel Mount
Catalog 5-1773450-5
Revised 3-13
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in millimeters USA: [phone]
unless otherwise specified. Asia Pacific: [phone]
UK: [phone]
For additional support numbers
please visit www.te.com