MAP200 Datasheet, PDF (1/2 Pages) TE Connectivity Ltd – KILOVAC High Voltage DC Contactors

KILOVAC High Voltage DC Contactors
KILOVAC MAP200 Series Contactor with 1 Form A (SPST-NO)
Contacts Rated up to 500 Amps, 12-900 Vdc
Product Facts
n Designed to be the
smallest, lightest weight,
lowest cost sealed contactor
in the industry with its
current rating for military
aerospace, ground vehicle
and naval, high current
applications
n Built-in coil economizer
(models requiring external
economizer also available)
n Optional auxiliary contact
for easy monitoring of
power contact position
n Hermetically sealed —
intrinsically safe, operates
in explosive/harsh
environments with no
oxidation or contamination
of coil or contacts, including
long periods of non-
operation
n Versatile coil and power
connections
n RoHS versions available
For factory-direct application assistance,
dial 800-253-4560, ext. 2055, or
805-220-2055.
Performance Data
Contact Arrangement, Power
Contacts — 1 Form A (SPST-NO)
Rated Operating Voltage —
12 - 900 VDC
Continuous (Carry) Current,
Typical — 500 A @ 85°C, 400 mcm
conductors
Consult Factory for required conductors
for higher currents
Make/Break Current at Various
Voltages ¹ — See graph next page
Break Current at 320VDC ¹ —
2,000 A, 1 cycle
Contact Resistance, Typ.
(@200A) — 0.2 mohms
Load Life — See graph next page
Mechanical Life — 1 million cycles
Contact Arrangement, Auxiliary
Contacts — 1 Form A (SPST-NO)
Aux. Contact Current, Max. —
2A @ 30VDC / 3A @ 125VAC
Aux. Contact Current, Min. —
100mA @ 8V
Aux. Contact Resistance, Max. —
0.417 ohms @ 30VDC /
.150 ohms @ 125VAC
Dielectric Withstanding Voltage —
2,200 Vrms @ sea level
Insulation Resistance @ 500VDC —
100 megohms ²
Shock, 11ms 1/2 Sine, Peak,
Operating — 20 G
Vibration, Sine, 50-2000Hz.,
Peak — 20 G
Operating Temperature —
-55°C to +85°C
Weight, Nominal — .95 lb. (.43 kg)
Notes:
1 _{Main power contacts}
2 _{50 at end of life}
Coil Operating Voltage (Valid Over Temperature Range)
Voltage (Will Operate)
Voltage (Max.)
Pickup (Close) Voltage Max.
Hold Voltage (Min.)
Dropout (Open) Voltage (Min.)
Inrush Current (Max.)
Holding Current (Avg.)
Inrush Time (Max.)
18-32VDC
32VDC
18VDC
10VDC
2VDC
4.5A
0.5A
100ms
Ordering Information
Typical Part Number ᮣ
MAP200 A R D E A
Series:
MAP200 = 500 Amp, 12-900VDC Contactor
Contact Form:
A = Normally Open
H = Normally Open with Aux. Contacts
Coil Voltage:
R = 28 Vdc, Mechanical Economizer
S = 28 Vdc, Electrical Cut-throat Economizer
Coil Wire Length:
A = 15.3 in (390 mm)
D = Coil connector on relay (requires option “E” or
“X” in next step).
Coil Terminal Connector:
N = No connector
E = 9-pin subminiature “D” plug mounted on contactor
housing
X = Special configuration (consult factory)
Mounting & Power Terminals:
A = Bottom Mount & Male M8 x 1.25 Thread Terminals
B = Bottom Mount & Female 1/4-20 Thread Terminals
D = Bottom Mount & Female M6 x 1 Thread Terminals
7–10
Catalog 5-1773450-5
Revised 3-13
www.te.com
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Dimensions are in millimeters USA: [phone]
unless otherwise specified. Asia Pacific: [phone]
UK: [phone]
For additional support numbers
please visit www.te.com