F4-A Datasheet, PDF (1/3 Pages) TE Connectivity Ltd – Automotive Relays Plug-in Mini ISO Relays

Automotive Relays
Plug-in Mini ISO Relays
Shrouded Power Relay F4 A
n Pin assignment similar to ISO 7588 part 1
n Plug-in terminals
n Customized versions on request
– Integrated components (e.g. resistor, diode)
– Customized marking/color
– Special cover with bracket
Typical applications
Cross carline up to 40A for example: ABS control, blower fans, cooling
fan, energy management, engine control, fuel pump, heated front screen,
lamps: front, rear, fog light, main switch/supply relay, wiper control.
Contact Data
Contact arrangement
1 form A, 1 NO 1 form C, 1 CO
Rated voltage
12VDC
12VDC
Limiting continuous current
NO
NO/NC
23°C, form A/form B
60A
60/45A
85°C, form A/form B
40A
40/30A
125°C, form A/form B
17A
17/12A
Limiting making current¹⁾
form A/form B
120A
120/45A
Limiting breaking current,
form A/form B
60A
60/40A
Limiting short-time current
overload current, ISO 8820-3²⁾
1.35 x 40A, 1800s

2.00 x 40A, 5s

3.50 x 40A, 0.5s

6.00 x 40A, 0.1s
Jump start test, ISO 16750-1
24VDC for 5min,

conducting nominal current at 23°C
Contact material
Silver based
Min. recommended contact load³⁾
1A at 5VDC
Initial voltage drop at 10A,
form A (NO), typ./max.
15/200mV
15/200mV
form B (NC), typ./max.
-
25/200mV
Frequency of operation at nominal load
6 ops./min (0.1Hz)
Operate/release time typ.
7.4/4ms⁴⁾
Electrical endurance
>1x10⁵ops
>1x10⁵ops
resistive load, NO contact
40A, 14 VDC 40A, 14 VDC
F136_fcw3c_bw
Contact Data (continued)
Mechanical endurance
>1x10⁶ops
1) The values apply to a resistive or inductive load with suitable spark suppression and
at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current
duration of maximum 3s for a make/break ratio of 1:10.
2) Current and time are compatible with circuit protection by a typical automotive fuse.
Relay will make, carry and break the specified current.
3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at
http://relays.te.com/appnotes/
4) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay
coil increases the release time and reduces the lifetime caused by increased erosion
and/or higher risk of contact tack welding.
Coil Data
Rated coil voltage
12VDC
Coil versions, DC coil
Coil
Rated
Operate Release
Coil
Rated coil
code
voltage
voltage
voltage resistance⁵⁾ power⁵⁾
VDC
VDC
VDC
Ω±10%
W
001
12
7.2
1.6
114
1.3
5) Without components in parallel.
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Max. DC load breaking capacity
Coil operating range
Coil 114,0 Ohm, 680 Ohm parallel resistor
30
Umax
25
136_OVR1
20
15
Uop (E=13,5V)
10
5
Uop (E=0V)
Load limit curve 1: arc extinguishes during transit time (changeover contact).
Load limit curve 2: safe shutdown, no stationary arc (make contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
10-2015, Rev. 1015
www.te.com
© 2015 TE Connectivity.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
0
-40
-20
0
20
40
60
80
Ambient temperature in °C
100
120
Does not take into account the temperature rise due to the contact current
E = pre-energization.
1
Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-
terms of the disclaimer and all chapters of
tion, application notes and all specifications
the ‘Definitions’ section, available at
are subject to change.
http://relays.te.com/definitions