English
Language : 

D-150-C-1X Datasheet, PDF (1/1 Pages) TE Connectivity Ltd – SIDE ENTRY REPAIR SLEEVE IMMERSION
CUSTOMER DRAWING
ADHESIVE
OUTER SLEEVE
PART
COLOR
DESCRIPTION CODE
D-150-C-11
D-150-C-12
D-150-C-13
D-150-C-14
Green
Red
Blue
Yellow
PRODUCT DIMENSION
I.D. (A)
Cut Length (B)
Adhesive
Sleeve
Adhesive
Sleeve
± .05 (.002) ± .05 (.002) ±1 .5 (.06) ±1 .5 (.06)
1.11 (.044) 2.29 (.090) 21.75 (.86) 19.05 (.75)
1.68 (.066) 2.74 (.108) 21.75 (.86) 19.05 (.75)
2.13 (.084) 3.43 (.135) 21.75 (.86) 19.05 (.75)
3.34 (.133) 4.80 (.189) 21.75 (.86) 19.05 (.75)
CONDUCTOR
Wire O.D. (Note*)
Min
Max
0.80 (.031) 1.10 (.043)
1.10 (.043) 1.50 (.059)
1.50 (.059) 2.30 (.090)
2.30 (.090) 2.80 (.110)
MASS
KG/1000 pieces
Min Max
0.165 0.202
0.198 0.242
0.261 0.319
0.332 0.405
MATERIALS
1. MELTABLE ADHESIVES: Environment resistant modified thermoplastic fluoroelastomer. Color coded
2. OUTER SLEEVE: Heat-shrinkable, transparent, radiation cross-linked modified fluoropolymer. Color coded
APPLICATION
1. These parts are designed to provide an environment resistant to repair damaged primary wire that have a radial crack up to 360
degrees, nicks/scrapes not longer than ¼” on the insulation rated for 135° C minimum and no damage to wire conductor. For
insulations procedures refer to RPIP 1101.
2. Install using Tyco Electronics approved convection or infrared heating tools in accordance with Tyco Electronics. When installed
with approved convection or infrared heating tools, assemblies will meet the performance requirements of TE D-6201 spec.
Infrared tools are not recommended for use with black cable jackets.
3 Temperature range: -65° C to +180° C. Product will withstand continuous temperature of 150º C for a period of 500 hours, and
continuous temperature of 180º C for a period of 168 hours.
NOTE*: If the O.D. of wire is out of the range that is specified in Table, use the next size of C-Wrap up or down.
W IR E O D
TITLE:
SIDE ENTRY REPAIR SLEEVE IMMERSION
RESISTANT, 150 DEG C,
RoHS COMPLIANT C-WRAP
Unless otherwise specified dimensions are in
millimeters.[Inches dimensions are shown in brackets]
Raychem
Devices
DOCUMENT NO.:
D-150-C-1X
TOLERANCES: ANGLES: ± 0°30’
0.00 ± 0.02 MM
0.0 ± 0.2 MM
0 ± 0.5 MM
ROUGHNESS
IN MICRON
Tyco Electronics Corporation reserves
the right to amend this drawing at any
time. Users should evaluate the
suitability of the product for their
application.
REV:
C1
DATE:
March 14, 2013
PREPARED BY:
TNGUYEN
CAGE CODE:
06090
ECO NUMBER:
ECO-13-004675
SCALE:
NTS
SIZE:
A
SHEET:
1 of 1
© 2013 Tyco Electronics Corporation. All rights reserved.
If this document is printed it becomes uncontrolled. Check for the latest revision.