C-2266017 Datasheet, PDF(1/4 Page) TE Connectivity Ltd – IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

C-2266017 Datasheet, PDF (1/4 Pages) TE Connectivity Ltd – IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION

THIS DRAWING IS UNPUBLISHED.

C COPYRIGHT 20

RELEASED FOR PUBLICATION

BY TYCO ELECTRONICS CORPORATION.

ATLANTIC VERSION

TERMINATOR

INTERFACE ADAPTER

PART

NUMBER

REVISION

2266017 -1

2266017 -2

2266017 -5

2266017 -6

2266017 -7

7- 2266017 -7

DESCRIPTION

FINE CRIMP HEIGHT ADJUST

NON-CRIMP HEIGHT ADJUST

FINE CRIMP HEIGHT ADJUST

CRIMP TOOLING KIT

FEED TYPE

MECHANICAL

PNEUMATIC

SERVO

LATCH PLATE 4

SERVO

4 LATCH PLATE 12

NONE

CONVERT TO

PNEUMATIC FEED

SERVO LATCH PLATE

SMART APPLICATOR

MECHANICAL FEED

SERVO LATCH PLATE

SMART APPLICATOR

MECHANICAL FEED

PNEUMATIC FEED

APPLICATOR DATA

CRIMP

SIZE

WIRE 2.03 mm [.080]

INSUL 4.06 mm [.160]

APPLICATOR INSTRUCTIONS

408-10389

TYPE

TERMINAL DATA: TE TERMINAL

TE CRIMP SPECIFICATION

TERMINAL NAME: 2.8MM SENSOR - FLAT TYPE RECEPTACLE

WIRE STRIP LENGTH

4.20-4.80 mm [.165-.189 IN]

TERMINAL

APPLICATION

C SPECIFICATION

(A)114-18144-0

(B)114-18144-1

INSULATION DIAMETER RANGE

n 1.40-2.10 mm [.055-.083 IN]

TERMINALS APPLIED

13 15

TE TERMINAL

C1__DWG_PN_1_0

TE TERMINAL

C1__DWG_PN_2_0

(A) 967542-1

C1__DWG_PN_1_1

(B) 968087-2

C1__DWG_PN_2_1

(A) 967542-2

C1__DWG_PN_1_2

C1__DWG_PN_2_2

(B) 968087-1

C1__DWG_PN_1_3

C1__DWG_PN_2_3

C1__DWG_PN_1_4

C1__DWG_PN_2_4

TE SEAL

C1__DWG_PN_3_0

TE SEAL

C1__DWG_PN_4_0

828904-1

C1__DWG_PN_4_1

WIRE

SIZE

1.00mm2

0.75mm2

0.50mm2

CRIMP HEIGHT

mm [INCH]

1.36+/-0.05 [.054+/-.002] W1__DWG_WGAUGE_1

1.27+/-0.05 [.050+/-.002] W1__DWG_WGAUGE_2

1.18+/-0.05 [.046+/-.002] W1__DWG_WGAUGE_3

CRIMP HEIGHT

REFERENCE SETTING

W1__DWG_CRIMP_HT_1

4.5

W1__DWG_CRIMP_HT_2

5.6

W1__DWG_CRIMP_HT_3

6.6

W1__FA_SETTING_1

W1__FA_SETTING_2

W1__FA_SETTING_3

1 RECOMMENDED SPARE PARTS

2 GREASE BEARING SURFACES LIGHTLY

3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION

SHEET SUPPLIED WITH THE APPLICATOR.

4 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT

ASSEMBLY. SEE BELOW FOR PART NUMBER:

MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8-

2266017 -4

PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8-

2266017 -4

SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST":

2266017 -5

SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST":

2266017 -6

5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE

APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS.

6 APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 62 & 180.

APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242.

FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEM 37 & 180.

7 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 252.

8 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY

ACTUATE THE COUNTER.

9 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE

APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE

NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD.

10 SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET

FOR ADDITIONAL INFORMATION.

11 TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE,

REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON THE BACK SIDE

OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL

INFORMATION.

12 WHEN ASSEMBLING -6 NON-CRIMP HEIGHT ADJUST APPLICATOR

USE SHIM PACK 2119957-2 TO ALIGN APPLICATOR'S MAXIMUM

WIRE CRIMP HEIGHT AT NORMAL TERMINATOR SHUT HEIGHT

13 THIS APPLICATOR APPLIES TERMINAL WITH A SEAL.

14 APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD

HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION.

APPLY #1-23419-5 LOC-TITE TO THREADS.

15 THIS APPLICATOR IS SPECIFIC FOR USE IN A STRIPPER SEAL TERMINAING UNIT.

AMP 4805 REV 31MAR2000

APPLICATOR STYLE CONVERSION CHART

PART NUMBERS REQUIRED

LOC

DIST

SET UP GAUGE

2119599-1

A 66

LTR

ECR-15-012887

ECR-17-000365

REVISIONS

DESCRIPTION

DATE

01SEP2015

11JAN2017

DWN

APVD

KH TE

TB GB

2119950-1

1338685-1

5-18022-5

2119641-1

2119799-1

2063440-1

2119951-1

8- 2266017 -5

1901094-3

1-1752354-7 2168400-6 (QUANTITY 2)

2161326-1

2119949-1

2119951-1

2161326-1

2119949-1

1338685-1

8- 2266017 -4

5-18022-5

8- 2266017 -5

8- 2266017 -4

5-18022-5

2119653-1

1901094-3

2119653-1

1-1752354-7

2168400-6

(QUANTITY 2)

----1-

-1-111

--1---

-11111

1803259-1

2119641-1

2119798-1

1-22279-3

2119758-1

2119082-9

BUSHING, FLANGED

FEED CAM, AIR FEED

DETENT PIN

SPRING, COMPRESSION

RAM, AMP STYLE, SIDE FEED, NON-ADJ.

CAM, SNAIL, INSULATION ADJUSTMENT

1803259-1

249

2119641-1

248

2119798-1

247

1-22279-3_SIMP

246

2119758

245

2119082-9

244

2119950-1

1338685-1

5-18022-5

2119641-1

2119799-1

2063440-1

-11111

2079764-1 WASHER, WAVE SPRING, CREST-TO-CREST

2079764

243

2119083

6- 1 1 1 1 1

2119083-1 RETAINER, INSULATION DIAL

242 D

7-18023-7

-11111

7-18023-7 SCR, SKT HD CAP M3 X 4.0

241

2168400-6

--22--

2168400-6 SHCS, LOW HEAD, RoHS, M5 X 16

240

2119580-1

-----1

2119580-1 MECHANICAL FEED ASSEMBLY

239

2063440-1

----1-

2063440-1 AIR FEED MODULE

238

--11--

2119740-2 TAG,IDENTIFICATION

2119740-2

213

--11--

1901094-3 SPACER, FEEDER

1901094-3

198

-11111

4-1722335-3 STRIPPER, SIDE FEED

4-1722335-3

182

-11111

1-5018030-0 NUT, HEX, REG, RoHS, M3.5

1-5018030-0

181

6- 1 1 1 1 1

1-1752354-7 STANDOFF,HOLD-DOWN

1-1752354-7

180

-11111

993111-1

PIN, SLOTTED SPRING 3.0 X 20.0

993111-1

177

-11111

5-22280-0 SPRING, COMPRESSION

SIMP_5-22280-0

176

-11111

1752353-3 GUIDE PIN,HOLDDOWN

1752353-3

175

-11111

1901680-2 GUIDE PIN,HOLDDOWN

1901680-2

174

----2-

21045-3

RING, RETAIN, EXTERN, 3/16 CRESCENT

21045-3

172

8- 1 1 1 1 1

994969-1

MAGNET, RARE EARTH HIGH ENERGY

994969-1_GATD

166

- REF REF REF REF REF

994970-2

COUNTER, MAGNETIC

COUNTER_994970

164

----1-

240638-1

SPRING, FEED FINGER

240638

163

----1-

3-23627-7 PIN, RETAIN, GRVD, 3/16 X .854

3-23627-7

137

----1-

2119799-1 HOLDER,FEED FINGER, AF

2119799

136

- - REF REF - -

SEE NOTE 4 MEMORY CHIP, PROGRAMMED

1901689_EMPTY_OCEAN_SF

135

--11--

1633743-1 SERVO FEED LATCH ASM

1633743-1

133

-11111

- - REF REF - -

1-18028-2

2119944-1

WASHER, FLAT, REG M4

FEED FINGER ASSEMBLY,SF

1-18028-2

119 C

2119944-1

117

-11111

455888-5

SPACER, CRIMPER

455888-5

-11111

2119956-1 DOCUMENTATION PACKAGE

2119956-1

-1--11

2119740-1 TAG,IDENTIFICATION

2119740-1

-22222

2168078-1 SCREW, DRIVE, RH, RoHS, 2 x .188

2168078-1

-1-111

2119793-1 LIMITER, ADJUSTMENT BOLT

2119793

6- 3 - 3 3 3

992763-5

SCR, SET, SOC, CONE POINT, M3 x 4.0

992763-5

-11111

2079383-4 SCR, BHSC, RoHS (M4 X 8)

2079383-4

----11

5-18022-5 SCR, HEX HD CAP, M4 X 6.0

5-18022-5

14 - 1 1 1 1 1

985575-5

SCR, FLT SKT HD CAP M3 X 16.0

985575-5

----11

1338685-1 PAWL, FEED

1338685-1

-44444

2168400-1 SHCS, LOW HEAD, RoHS, M4 X 12

2168400-1

----12

18023-9

SCR, SKT HD CAP M4 X 6.0

18023-9

-----1

2119652-1 FEED CAM, PRE FEED

2119652

-----1

2119653-1 FEED CAM, POST FEED

2119653

-11111

2-2119656-1 APPLICATOR BASIC ASSEMBLY, SF

2-2119656-1

-1-111

2119370-1 RAM, AMP STYLE, SIDE FEED

2119370

-11111

2079383-7 SCR, BHSC, RoHS (M8 X 25)

2079383-7

-1-111

2119645-1 DISC, NUMBERED FA WIRE ADJUSTMENT

2119645

-1-111

2119957-1 APPLICATOR SHIM PACK

2119957-1

-11111

2119644-1 RAM WASHER, PRECISION

2119644-1

6- 1 1 1 1 1

7- 1 - 1 1 1

2119085-1

2119092-1

FA HEAD, ATLANTIC STYLE

BOLT, ADJUSTMENT

2119085_PRE_REV_K

2119092-1

-11111

1752356-4 SUPPORT, TERMINAL

1752356-4

-22222

2079383-5 SCR, BHSC, RoHS (M4 X 20)

2079383-5

-11111

2161328-1 HEX HEAD, FLANGED, M5 x 8mm LONG

2161328

-11111

1-1320908-2 SPACER, STRIP GUIDE

1-1320908-2

-11111

2119959-2 ASSEMBLY, STRIP GUIDE

2119959-2

*WARNING

ON INSTALLATION, SET WIRE DISC, ITEM 40 TO

LARGEST WIRE SIZE SETTING. USE OF SETTINGS

BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING

-11111

11 1 - 1 1 1 1 1

-11111

455888-3

1320928-2

2119806-1

3-22280-3

1-356885-4

SPACER, CRIMPER

STRIP GUIDE

INSERT, SHEAR

SPRING, COMPRESSION

STOP, SHEAR

455888-3

1320928-2

2119806

SIMP_3-22280-3

1-356885-4

WILL CAUSE DAMAGE TO CRIMP TOOLING.

1- 1 1111

2119805-1 SHEAR HOLDER, FRONT

2119805-1

1- 1 1111

318707-1

FLOATING SHEAR, FRONT

318707-1

1111111

------

1333204-1

ANVIL, COMBINATION

1333204-1

ITEM_7

------

ITEM_6

-11111

2119781-1 DEPRESSOR, SHEAR

2119781-1

-11111

238011-9

BLOCK, CRIMPER SPACER

238011-9

--1---

7- 1 - 1 1 1

----1-

2119957-2

8-21084-0

2119640-1

APPLICATOR SHIM PACK

O-RING, .676 ID, .070 DIA. MAT.

PUSH ROD, AIR FEED

2119957-2

260

8-21084-0_GATD

252

2119640-1

250

11 1 1 1 1 1

-11111

11 1 1 1 1 1

3-2119784-1

1-455888-0

1-456405-6

CRIMPER, INSULATION O PREMIUM

SPACER, CRIMPER

CRIMPER, WIRE PREMIUM

3-2119784-1

1-455888-0

1-456405-6

-77 -7 -6 -5 -2 -1 PART NO

DESCRIPTION

ITEM

ATLANTIC VERSION

Shown on sheets 1 of 4 & 2 of 4

(Pacific version shown on sheets 3 of 4

& 4 of 4)

-77 -7 -6 -5 -2 -1 PART NO

DESCRIPTION

ITEM A

THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION

IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION

SHOULD BE CONTACTED FOR THE LATEST REVISION.

DIMENSIONS:

MATERIAL

TOLERANCES UNLESS

OTHERWISE SPECIFIED:

0 PLC

1 PLC

2 PLC

3 PLC

4 PLC

ANGLES

FINISH

DWN

X.ZHAO

CHK

T.ELBIN

APVD

T.ELBIN

PRODUCT SPEC

13AUG2013

13AUG2013 NAME

APPLICATION SPEC

WEIGHT

SIZE

CAGE CODE

A1 00779

Customer Accessible Production Drawing

TE Connectivity

Harrisburg, PA 17105-3608

Ocean Side Feed

Applicator

DRAWING NO

RESTRICTED TO

2266017

SCALE

SHEET

1:2

REV

SHEETS 3 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION

▷