C-2143307 Datasheet, PDF (1/5 Pages) TE Connectivity Ltd – THIS DRAWING IS A CONTROLLED DOCUMENT.

8
THIS DRAWING IS UNPUBLISHED.
C ^{COPYRIGHT 2008}
TE CONNECTIVITY
RELEASED FOR PUBLICATION
ALL RIGHTS RESERVED.
7
2008
D
3 MAX TYP
DETAIL S ₁₂
SCALE 20:1
C
6
5
4
1 _{CAGE ASSEMBLY MATERIAL: NICKEL SILVER, 0.25 THICK}
HEAT SINK MATERIAL: ALUMINUM
HEAT SINK CLIP MATERIAL: STAINLESS STEEL
EMI SPRING MATERIAL: COPPER ALLOY
FRONT FLANGE MATERIAL: ZINC ALLOY
LIGHT PIPE MATERIAL: CLEAR POLYCARBONATE
2 _{PITCH BETWEEN PORTS OF ONE 1X6 CAGE ASSEMBLY.}
3 _{SPACING BETWEEN CAGES ON THE SAME PC BOARD, TO BE SPECIFIED BY}
CUSTOMER, MUST COMPLY WITH MINIMUM DIMENSIONS SHOWN.
4 _{REFERENCE APPLICATION SPEC 114-13218 FOR RECOMMENDED DRILL HOLE}
DIAMETER AND PLATING THICKNESS.
5 _{DATUMS AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER.}
6 _{DIMENSION F IS THE NOMINAL THICKNESS OF CUSTOMER SUPPLIED PC BOARD,}
SINGLE SIDED PC BOARD MINIMUM THICKNESS = 1.45mm
DOUBLE SIDED PC BOARD MINIMUM THICKNESS = 2.2mm PER QSFP.
7 _{HEAT SINKS, LIGHT PIPES, AND HEAT SINK CLIPS SHIPPED ASSEMBLED TO CAGE}
ASSEMBLY.
8 _{DATUM A IS TOP SURFACE OF PC BOARD.}
9 _{DIMENSION APPLIES WITH MODULE INSERTED IN CAGE.}
10 _{UNPLATED THRU HOLE.}
11. MATES WITH QSFP MSA COMPATIBLE TRANSCEIVER.
12 _{SURFACE TRACES PERMITTED WITHIN THIS AREA EXCEPT WHERE CAGE STANDOFFS,}
SHOWN IN DETAIL S, CONTACT PC BOARD.
13 _{BASELINE FOR THESE DIMENSIONS IS THE CENTER OF COMPLIANT PIN HOLE.}
14 _{2D BARCODE AND DATE CODE (YYWWD) MARKED ON SIDE OF CAGE.}
( 60.57 )
(D)
9
B
MAX
2.2 MAX
(C)
B
2D BARCODE AND DATE CODE
14
SEE DETAIL
S
3
2
1
LOC
DIST
GP 00
P
LTR
A
REVISIONS
DESCRIPTION
RELEASE TO A PER ECO-15-018552
DATE
28DEC2015
DWN
APVD
RG SH
15 _{REFERENCE APP SPEC 114-13218 FOR GASKET THICKNESS CALCULATION.}
16 _{EMI SPRING FINISH: 2µm MINIMUM TIN}
FRONT FLANGE FINISH: 3µm MINIMUM TIN OVER 1.27µm MINIMUM NICKEL
OVER 5.08µm MINIMUM COPPER.
HEAT SINK FINISH: NICKEL OR BLACK ANODIZED
D
17 _{HEAT SINKS AND CLIPS SHIPPED ASSEMBLED TO CAGE ASSEMBLY.}
LIGHT PIPES, SHIPPED UNATTACHED, MUST BE ASSEMBLED BY CUSTOMER
AFTER THE CASE IS SEATED IN THE PCB.
C
( 117 )
5X ( 19 ) ₂
B
CAGE ASSEMBLY
A
4805 (3/11)
EMI SPRING
FRONT FLANGE
7
0.8-1.1
2.8
1.70
23.0
NETWORKING
2143307-3
7
0.8-1.1
2.8
1.70
16.0
SAN
2143307-2
17
0.8-1.1
2.8
1.70
13.7
PCI
2143307-1
HEAT SINK
PART
E
D
C
B
PROFILE
NUMBER
A
THIS DRAWING IS A CONTROLLED DOCUMENT.
DIMENSIONS:
mm
MATERIAL
-
-₁
TOLERANCES UNLESS
OTHERWISE SPECIFIED:
0 PLC
1 PLC
2 PLC
3 PLC
4 PLC
ANGLES
FINISH
-
0.1
0.1
0.013
0.0001
-
-
1- 6
DWN
04MAR2010
C. VALENTINE
CHK
04MAR2010
J. PETERSON
APVD
04MAR2010
J. PETERSON
PRODUCT SPEC
108-2286
APPLICATION SPEC
114-13218
WEIGHT
-
CUSTOMER DRAWING
TE Connectivity
NAME
1X6 CAGE ASSEMBLY, BEHIND BEZEL,
W/ LIGHT PIPES AND HEAT SINKS,
QSFP
SIZE
CAGE CODE
DRAWING NO
RESTRICTED TO
A1 ⁰⁰⁷⁷⁹
2143307
SCALE
SHEET
3:1
OF
15
-
REV
A