C-2098190-1 Datasheet, PDF (1/1 Pages) TE Connectivity Ltd – THIS DRAWING IS A CONTROLLED DOCUMENT.

4
3
THIS DRAWING IS UNPUBLISHED.
C ^{COPYRIGHT 20}
BY -
RELEASED FOR PUBLICATION
20
ALL RIGHTS RESERVED.
PERFORMANCE DATA
PARAMETERS
UNITS
VALUE FOR EV200 SERIES
Contact Arrangement: Power Contacts
D
Rated Operating Voltage
Vdc
1 Form X
100 - 900
(SPST-NO-DM)
(NOTE: Voltages between 450 to 900 Vdc are capable but load dependent and
require TE Engineering approval)
Continuous (Carry) Current, Typical
A
500
@ 65 $ C, 400 mcm conductors
Consult factory for required conductors
for higher (500+ A) currents
Break Current at 320 Vdc
A
2,000, 1
cycle
Contact Resistance, Typical (
@ 200A)
mohms
0.2
Load Life
Cycles
See Chart
Mechanical Life
Cycles
1,000,000
Operate Time @ 25 $ C
Close (includes bounce), Typical
ms
15
Bounce (after close only), Max
ms
7
Release (includes arcing), Max
@ 2000A ms
12
Dielectric Withstand Voltage
C
Vrms
2,200
@ sea level (leakage<1 mA)
Insulation Resistance
@ 500 Vdc
megohms
100 (50 at end of life)
Shock, 11ms 1/2 sine, peak, operating
G
20
Vibration, sine, 80 - 200 Hz, peak
G
20
Operating Ambient Temperature
$C
-40 $ to
+85 $
Weight (Nominal)
lb [kg]
.95 [0.43]
COIL DATA
Voltage (will operate)
Voltage (Max)
Pickup (close) Voltage (Max)
Hold Voltage (Min)
Dropout (open) Voltage (Min)
Inrush Current (Max)
Holding Current (Avg)
Inrush Time (Max)
B
9 - 36 Vdc
36 Vdc
9 Vdc
7.5 Vdc
6 Vdc
3.8A
0.13A
130 ms
@ 12V
Coil Wire is 22AWG
with 15.3 IN [390mm] Length
STAINLESS
.55 # .025
[14.04 # 0.63]
A
1. TO AVOID OVERHEATING, THE COIL ABOVE SHOULD NOT BE LEFT ON AT FULL POWER
(12V) FOR A LONG PERIOD OF TIME.
2. THE MINIMUM HOLD CURRENT OF 650mA (MENTIONED ABOVE) ONLY PRODUCES A T-RISE
OF 20 $ C (MAX).
3. FOR ANY OTHER INFORMATION, PLEASE REFER TO THE EV200 GENERAL CUSTOMER
1471-9 (3/13)
DATASHEET.
2
1
P
LTR
C
D
REVISIONS
DESCRIPTION
REVISED PER ECO-12-015617
REVISED PER ECO-15-005163
DATE
28AUG2012
02APR2015
DWN
APVD
DD AL
DD AL
D
M8 x 1.25 POWER TERMINALS
(Hardware Supplied):
2 x M8 Washer, Stainless
2 x M8 Lockwasher - Split Ring, Stainless
2 x M8 x 1.25 Nut, Stainless
Torque 80 to 100 in-lb [8.8 to 11 Nm]
1.05
[26.67 # 0.26]
A1 "+" POSITIVE
TERMINAL
Mounting Hardware (Not Supplied):
2 x M5 Bolt
2 x M5 Lockwasher
2 x M5 Narrow Washer
Torque 15 to 30 in-lb [1.7 to 3.3 Nm]
A2 "-" NEGATIVE
TERMINAL
C
2.688 # .01
[68.28 # 0.26]
1.65 .01
[42.0 # 0.26]
RED = "+" COIL
BLACK = "-" COIL
2.85 # .025
[72.3 # 0.63]
2.20 # .025
[55.81 # 0.63]
LABEL
B
2.05 .02
[52.0 # 0.51]
2.44 # .02
[62.0 # 0.51]
.50 .01
[12.6 # 0.26]
3.17 .01
[80.48 # 0.26]
2098190-1
PART NUMBER
THIS DRAWING IS A CONTROLLED DOCUMENT.
DIMENSIONS:
TOLERANCES UNLESS
OTHERWISE SPECIFIED:
DWN
A. LEE
CHK
A. LEE
APVD
25MAY2010
25MAY2010
25MAY2010 ^NAME
TE Connectivity
A
INCHES
A. LEE
RELAY,
0 PLC
-
1 PLC
-
2 PLC
.01
PRODUCT SPEC
-
EVC500 SPST-NO 12V
3 PLC
.005
APPLICATION SPEC
4 PLC
ANGLES
-
1$
-
SIZE
CAGE CODE
DRAWING NO
RESTRICTED TO
MATERIAL
-
FINISH
-
WEIGHT
-
A2 ⁰⁰⁷⁷⁹
2098190-1
-
-
-
CUSTOMER DRAWING
SCALE
SHEET
1:1
OF
11
REV
D